Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I'm using segger IDE for EVK-NINA-B1. I've downloaded nRF5_SDK_16.0.0 and trying yo run one of its example but getting error like stray '#' in program. I've attached 2 pictures...
Hi,
I'm using NRF52832 SDK15.2 to develop a smart band. Each time reconnect with iphone, the application assert in the peer manager event handler pm_evt_handler().
Any...
Hi Team,
I would like to know what does the system do after I call system off function as per below:
I have check through the oscilloscope to check how's the system...
Hi Team,
I am in the UK and trying to get an evaluation sim from Vodafone for NB-IoT. However they have set a limit of 2 IP addresses and hence I need the IP address of...
I'm developing bluetooth logging software on the nRF51 DK using SDK 12.3.0. We had been developing for some time in mbed, but were advised to switch over to Keil using the...
Hi,
I'm working on sending reliable message from server to client, the models are modified from RSSI model.
When I tring to send messages to client it will keep sending...
I've been trying to store an array (SDK16,S332)
uint8_t my_data[]={0x00,0x01,0x02,0x03,0x04,0x05,0x06,.........0x23}
using fstorage I wrote an update function :
I hardcoded...
To the kind attention of Nordic support team,
I'm trying to do things like in https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059...
Hi,
I have a project which was originally written using SDK12, and have updated it to SDK16, I am sorry I know this question seems to have been asked in many different ways...
Dear,
Like I said in the title, I did use the NFC of my PCA10056 with my phone, it works, I also can read some information from nRF52840 by NFC. Right now, I programmed...
Hi Devzone:
I am working on nRF52840 with latest SDK.
I have 1 differential pair and 1 single ended pin I want to sample, single ended samples at every 40ms while differential...
I was trying to connect my cellphone tu the ublox modulo for sends at commands from my cell, in the main program of the micro I've the next lines for turn on the ublox module...
i have a nrf52840 dk
i need to connect the flex sensor to the board and know the resistance value while bending
how to do it?
and what code should i dump
Hi there,
I have developed the custom board with nrf52832 Soc and programmed blink code, it works fine.Now i uploaded the ble DFU template example and updated firmware...
I can't install the tool chain.
Looks like I have to install something called chocolatey?
I can't install chocolatey. I tried the chocolatey website for help and was baffelled...
