I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi!
24 days have passed since I was promised an update (which I hope will mean a solution), but nothing...
Also, there is no updated Getting Started Assistant and the...
Hi,
We are planning to use an Automotive Grade Bluetooth SoC in one of our new designs.
Some controllers in the nRF51 family seems to be Automotive Grade, but we also...
I tested with Light Switch Example in nrf5_SDK_for_Mesh_v3 version, I have set Transittion time to 160 second and Delay to 0, problem occur is the device Cann't countdown...
Hi,
I am using an nrf52840 MCU, Nordic SDK 16.0.0 and IAR Workbench for ARM v8.40.1.
The MCU has the following configuration:
- MBR installed
- DFU secure bootloader...
Hello everyone,
I faced with bus fault after running beacon example from mesh_sdk. It occurred after calling mesh_provisionee_prov_start().
Unfortunately, I didn't found...
Greetings...
Provisioning w/ Android tool only works when board is connected to debugger.
Provisioning failed to even find the devices when scanning after disconnected...
When enabling 3 instances of SPIM (1,2,3) on NRF52840 the application doesn't start at all.
Weirdly however, the application works fine when SPI3 takes SPIM3 and the rest...
Hi,
Does SoftDevices v7.0.1 supports Multiple Advertising Sets feature? I read that Softdevice v6.1.0 does not support the Multiple Advertising Sets feature. Let me know...
Hi. I was wondering if maybe you know where can I find the PCB desing of any of this modules: NRF24L01+ (the black one) or the SMD version. I only can find those pictures...
Hi gays,
Now, I want to c ollect a pulse waveform(example : 1s, 50% duty cycle ) which accuracy requires milliseconds resolution and I use PPI to read a capture value from...
Hi,
We have a custom board that uses an nRF52840. All our development is done on Win 10 based PCs. Our custom board is connected to our Win 10 based PC via USB and when...
Hello Sir,
We are using NRF24L01+PA+LNA SMA Antenna for transmission purpose using arduino using RH_NRF24.h library.
It is been set to 0dBm transitting power by default...
Hello,
I am working with nRF SDK V 16.0.0. I am using peer manager for my application, can I store my application data too using peer manager? if yes, please help to do...
