Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I am trying to develop a low power scanner with nrf52832 which is is acting as both central and peripheral (beacon)
I need to detect other tags like itself transmitting...
Hi,
is there any example of firmware that can be used on nRF24LU1P that perform some data receiving on RF side and send them over USB?
The most important part is the USB...
Hello, We have designed a PLE peripheral based on nRF52840, SDK16.0, Softdevice v7.0.1. We have having an issue where, occasionally, we send a certain data (a command) to...
Hi everyone,
I created a custom service that I want to be advertised through scan response. Also, I want to advertise the INFORMATION SERVICE through advertising data. I...
Hi, I'm working with nRF52840 with NFC. I don't have yet the external antenna to connect to (now I'm using uFL), but I'm not sure about the trace width that goes from the...
MeshSDK: 3.2.0
StockSDK: 15.2
Hello,
I have a network where the sequence numbers have become corrupt due to removing devices from a network and then provisioning other...
Hello,
I've been trying to write my own library that uses UART.
I went through the "uart" example and wrote this piece of code.
uart.c
gpio.c
main.c
...
I would like to ask you a question, that is, the RTC in the chip of 52832, in the case of non-power-off restart, is there any way to keep the RTC time and continue the timing...
I am trying to extract the gps coordinates and use CoAP to sent the info to Telenor IoT server. I am using the gps demo code provided by Nordic .
https://github.com/NordicPlayground...
Hello,
I want to program nRF5340 via UART.
What is the hardware related event that puts the application processor in program mode over the UART ?
All ARM microprocessors...
Hi
OS: Windows 10 (32-bit)
nRF Connect application: v3.3.1
Getting started assistant: v3.3.1
Please see the attachment. After installing ninja, tried to verify it...
I`m searching after an application document / description of a test setup, how to measure BLE data throughput with our product including nRF52840. Maybe Nordic have a smart...
I've been programming in SES for several months now, and I need to put the code into libraries to keep an overview of my project.
I've been able to include SDK libraries...
hi, I used NRF52833 to debug the program, and I used the ble_app_hid_mouse project in SDK16 to debug the fstore function ,and the file path is E:\nrf52833\nRF5SDK160098a08e2...
Hi everyone,
This is my first time using Nordic nRF SDK, so i hope that I'm not asking for anything too stupid, I'm having troubles in adding nrf_logger.h into a project...
