Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
The issue is that after a buttonless DFU is completed the new firmware runs as expected but the new advertised name doesn't change.
device name in firmware before DFU...
Hi Team,
Currently i'm working on Openthread Border router(Rasberrypi) with nrf52840 as a radio. I have gone through IOT SDK(Nrf5) for enabling the 6lowpan BLE Border router...
I tried to update SD + APP at the same time but it only uploads the SD. I create the zip file like this nrfutil pkg generate --hw-version 52 --application-version 1 --application...
Howdy,
I'm porting a GATT profile from a different profile where the custom services characteristics and descriptors UUIDs are malformed. For example;
1st Custom Service...
This issue exists in NRF SDK5 15.2.0 and earlier. NRF log module has entered "production" level as of SDK5 15.2.
While implementing an additional logging backend, I discovered...
how to change the twi sensor coding to get the X,Y,Z AXIS for the position of the gy-80 module
this module has
1. HMC5883L
2. BMP-085
3. L3G4200D
4.ADXL345
at...
Hello,
I would like to append data to a coap response like this:
I have a response handler that is triggered as the device receive the response. I am able to get the...
Hello guys,
I am trying to run the mqtt_simple sample. I tried to do so on both nrf9160_pca10090ns and nrf9160_pca20035ns. The application builds fine for both boards...
Hi,
Does nRF52840 on Thingy 91 and nRF9160 DK has a unique MAC-address? Or is it a randomized MAC-address with a high probability of being unique in the user's environment...
Hi,
Is there a way for the application layer to be aware of what the modem Tx power is? We would like to know for purposes of warning customers if they have placed a device...
I know that as per definition the connection interval is the time between two connection events.
So does it mean that if the connection interval duration is low then number...
Hey guys,
I have nRF52840-DK and one time i got pop-up from nRFgo Studio, that i need newer version of Jlink. I updated Jlink from Segger website to version 6.62b. After...
To the kind attention of Nordic support team,
Is it possible to change pipes' numbers used by secured gazell library? It seems to be using pipe0 for pairing infos and pipe1...
Hi, I have a quick question regarding the DFU MTU get request.
According to the docs page , this should return the MTU used by the transport, but in reality nothing is transmitted...
Hi,
nRF9160 DK (PCA10090) is continuously rebooting.
I have flashed following Images and tested, but same issue (rebooting continuously) observed.
1. Pre-compiled...
