after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I try to create coap server project and it should by updateable by DFU. I merge project simple coap server and thread dfu client, and I keep instructions in documentation...
Hello Everyone,
I am Using Nrf51822 module and s130_nrf51_2.0.1_softdevice . my actual function nrf51822 twi interface with stc3115 Gas gauge IC .read the battery voltage...
Hello,
I am implementing ble advertising using below code, i encountered a strange behaviour with this code. If jlink is connected the advertising works just fine. if I...
I have created one characteristic in which i am trying to write multiple bytes at the same time i want to use that for further processing, how to access that whole data which...
Hi,
I just started working with Nordic nRF52840 serial interfaces,can you please tell me which one is best for serial communication among SPI and I2c and why?And can you...
Hi Nordics, I know it has been asked over and over again about doing DFU of slave nrf52 using a central nrf52. devzone.nordicsemi.com/.../ota-dfu-application-firmware-by-ble...
Hi we are trying to program code using the SDK v12.3 library onto a custom NRF51822 board using SES. The custom code contains B luetooth routines, GPIO routines, and TWI routines...
PlatformIO team is pleased to announce the release of Nordic nRF51/52 development platform . This release introduces many new features and performance improvements. The notable...
Hi all,
I am trying to deploy the long range mode with nRF52840. I modified the blinky example under SK 16.0.0 and it just keeps resetting
and the error code is 0x0007...
I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
Please help me sort out one question.
I have a peripheral device that stores an archive with data. At a certain point, the archive is transferred to the central device...
Hello,
We are focussing on the nRF9160 to build a IOT datalogger.
We would like to intergrate an micro SD card.
Now, I mis the 4-bit SPI interface ( SDIO), and I asked...
Greetings,
A very bizarre thing is happening. This is the umpteenth time I'm working on a peripheral driver and the code gets stuck at 'NVIC_EnableIRQ(UARTE0_UART0_IRQn...
I would like to implement Bluetooth 5 packet exchange without the softdevice.
How can we convert the
nRF5_SDK\examples\peripheral\radio\receiver
nRF5_SDK\examples\peripheral...
How can you use assisted GPS(AGPS) in nRF9160?
Let's say you get assisted data from "supl.google.com" and how do you set this address in code?
Do you have to wait for...
