Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
Hi
I merged the AGPS to serial_lte_modem slm_at_gps.c but it did not work:
1, if I activate LTE in gps_thread_fn(), it will be failed in supl_session();
2, If I activated...
I am trying to read through the nordic 52832 i2c an accelerometer datum lsm303dlhc using the example "twi sensor".
The code used is written below.
Unfortunately, the code...
SDK: 15.1 SoftDevice: S132, v6.1 IDE: Keil Hello I am using the nRF dongle combined with nRF Connect on my PC to connect to my BLE peripheral (custom board). During connected...
Hi there,
I am trying to update the advertising packet (specifically update the battery service value).
I cannot make it work and the function return an error.
Has this...
I want to make serial connection in between an nRF52833 and a LPC1752.
When I use the UART in a firmware without using the SoftDevice for Mesh 4.0.1 , everything is working...
Hi,
I am using a Linux Host to communicate with my nRF52840 as a USB CDC ACM device. As a test, I ran minicom and was able to transfer bytes to my Nordic app successfully...
Gentlemen:
I'm new to Nordic processors, but I have implemented projects with Silabs Gecko and ATTiny processors in the past. I'm working on a project for a consumer product...
Hello,
I have installed Embedded Studio and acquired a Nordic license. However the Tools/Options... nRF Connect menu option does not appear. I tried creating a dummy Nordic...
The project for nRF51822 was developed on base of example ble_peripheral ble_app_hrs for pca10028/s130 with an additional vendor specific service with 128-bit UUID for an...
I have a strange problem. We built 100 custom boards. I've only checked about 50 boards so far. 47 boards work properly. 3 do not.
We used secure_bootloader_uart_pca10056...
Hi support team
One of our customer ask if it's possible to transfer a file system(LittleFS,refer: https://github.com/ARMmbed/littlefs ) to our Soc?? If not, are there some...
I am new to BLE and I am exploring Introduction to service. However I am stuck with Step 1 and Step 2. Is Step 1: static ble_os_t m_our_service; (to declare a service) and...
I have a device with no OS on it that talks serial through a UART to a nRF53840. I need to be able to update the nRF53840's firmware across the serial link, but since I don...
Hello, I am working on the BMD-300 Series Evaluation Kit with nrf52832 microcontroller and I tried accessing the serial number of my nrf52832, with these functions:
m_device_id1...
One doubt, if a node gets reset or disconnected , due to power failure in openthead cli mesh, dose it need to get configured again to join the mesh or will it connect to mesh...
