I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Tsu_dat (300ns min) and Thd_dat(500ns min) are more stringent than NXP I2C spec .(Fast mode)
Since most IC vendors design their I2C bus with NXP I2C spec, they are not meeting...
Greetings,
The only examples I can seem to locate of using the Coexistence Interface on nRF9160 is with the internal GPS but the documentation states that "COEX0: Input...
hi... i want to store data in flash , i will get the data periodically . Even i am writing data to flash using write command ,when i am trying to print the data which is stored...
I am using nRF52 DK.
When I do 2 analog inputs using the SAADC, I noticed that, in the SAADC callback, p_event->data.done.p_buffer[0] corresponds to the correct SAADC channel...
Hello,
I use a configuration with multiple NUS_C and NUS links. When I receive events, how to know the index ?
I have seen mutiple exemples using conn_handle but in a...
Hi teams,
I am trying to automate preferred mesh configuration for each node.
For example, if I use nRFMesh app, I should 1) bind application key to each model, 2) set...
Hi everyone,
During test with my small mesh network, I found that adding all-nodes to subscription list is prohibited by Mesh Specification.
In Mesh Profile 4.3.2.19,...
Hi:
I use the sdk https://github.com/jimmywong2003 to make a bin file and then run the command of ./UartSecureDFU ttyACM0 application.zip to updgrade in linux
It always...
Hi
if one searches the examples using the timeslot API, every application seems to do it's own timeslot cleanup. Also documentation is not very clear about this.
Best...
i am using nrf52840 dongle with uart using ble_app_interactive example,
but after commenting only uart with cli is replying with some text as shown in image .
For the...
Hi! I'm using S140 and I'm using the ble_advertising module to set up advertising.
This is my advertising_init function which is working properly until I uncomment the enabling...
This is perhaps not so much a question as a request.
The FDS event handler, type `fds_cb_t`, has only one argument, type `fds_evt_t`, unlike (say) the two wire event handler...
Hello,
I would like someone to explain to me payload for Zigbee cluster library (Zcl)
i was following this guide to control my lights:
https://infocenter.nordicsemi...
I am trying to connect to another type of board via the UART on the development kit. However, there seems to be a voltage mismatch. Are the nRF52840 development kit UART signals...
