nRF54L15 would be used as thread RCP, host processor would use uart to communicate with the rcp. They would behave like a OTBR.
I also need to do device firmware update...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
[ Just figured out it doesn't work the way I thought ]
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but...
I merged the code from the SDK examples "usbd_audio" and "usbd_cdc_acm" and have ensured that each has their own INTERFACE and ENDPOINTS. I am able to download to the development...
Hi,
I am developing with nRF52832, SDK 15.3
I have an issue with sending data over NUS service. When I flash the code to nRF, it starts advertising, but when I connect...
Dear sir,
The twi sensor code in SDK14 is getting stuck at NRF_BREAKPOINT_COND. Also, on the uart terminal it is showing FATAL ERROR . Please help me out of this.I am using...
Hi
I want to set up a network of about 4 groups of BLE light modules(using the experimental dimming example). Each group comprises of 5 to 7 light modules.
Currently the...
Hello, my code was working just find then I tried to add the user description value to my characteristic. In the example below I had set it to "Test" for now. Once I did this...
hi
i am programing BLE blinky app blinky which advertise. yes, the same code i am trying on custom board works on nrf52DK which has LFRC crystal activated as mentioned on...
I am trying to add my nrfcloud certificate to my nrf9160-DK but the AT commands do not work due to a timeout.
My procedure is as follows:
1) Downloaded the "nrf9160dk_fw_2020...
Hello Nordic team,
I'm getting started with BLE, using the 52832 SDK16 HID mouse example. In the example, clicking the button only moves 5 pixels. How can I move the cursor...
Hi! When measuring current draw with the NRF52 in idle state, we've noticed current spike at seemingly random times. when investigating further, we've discovered these spike...
Hi,
I am looking for an implementation on DotDot App layer over Thread and couldn't find it anywhere. I want to implement dot-dot for Light, Temperature and Humidity Sensors...
Hello, I want to purchase an nrf52 development board. I am currently using nrf52832 module (MDBT42). I wonder which DK should I purchase nrf52832 DK or nrf52840 DK? I am asking...
Hi,
I am trying to store data to flash with the support of FDS module while using Mesh. I'm currently using NRF52832 with NRF5 SDK 15.0 and Mesh 4.0.
I have tested flash_fds...
Hi Support Team
I try to run the http_client sample based on ncs1.2.0, and I use the following configs because only NB-Iot available in our location:
when start running...
Hello there,
We faced the new issue after the iPhones are updated to the iOS 13.4. I tried to find the issue solving on the forum and looks like it is the new one.
We...
Hi,
I'm evaluating the new nRF5340-PDK and trying to put the device in low power mode. My steps so far:
Cut SB40 to allow measuring current via P22.
Connect power...
