This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hi ,
I am following the instructions here:
https://bifravst.gitbook.io/bifravst/bifravst-on-aws/simulator
to deploy the web application, and the web application says...
Based on SDK15.3(nRF52810) app_uart example, stop the adverting, turn off all the peripherals and enter idle_state_handle(), but the static current is still about 10uA. Rememeber...
I set up the environment for the nRF9160 as it was specified and downloaded the git-hub code https://github.com/NordicPlayground/fw-nrfconnect-nrf (environment 1) and I tested...
Hi all,
I am using 2 SPI's in my design. I enabled SPI0_ENABLED and SPI1_ENABLED in my sdk_config.h.
SPI0 works fine. But SPI1 MOSI pin always sends 0xFF.
My pin configuration...
Hi, I m sending a packet in mode Nrf_1Mb to another board nrf5340-PDK.
When I try to enable NRF_REGULATORS_S->VREGRADIO.DCDCEN=REGULATORS_VREGRADIO_DCDCEN_DCDCEN_Enabled;...
Hi,
I am using mesh SDK v3.2.0 and SoftDevice(s140 v6.1.1) to build light switch server firmware. And also insert the uart code from nRF5_SDK_15.3.0_59ac345. So the light...
Hello:
I am studying thread samples in nRF9160.
There are two thread samples: "zephyr\samples\basic\threads" and “zephyr\samples\synchronization”.
But I can't find main...
Hello,
I received information that i could turn the modem on and off not more than 60 times within an hour.
We are however working on a real time system, which may...
Hi everyone,
Currently I am routing hardware for an upcoming project using the nRF5340 and it's time for a sanity check.
The goal is that the HW works well enough w/Engineering...
Hi,
I've been trying to set up a SPI <-> USB interface between an FPGA and my PC via the nrf52840 dk. My ultimate goal is to stream 1Mbps+ worth of data, but right now I...
I have a custom characteristic on which I send ASCII strings as notifications similar to NUS. Is there a way to have the Bluetooth Low Energy app in nrfConnect show the data...
I am writing a BLE application on the nRF52832 using S132 v6.0 and SDK 15.2, and my application is using the nrfx_SPIM driver. I find that once I initialize the spim driver...
I am using the nRF52840, SDK 16.0.
I'm attempting to advertise on the coded phy and the 1M phy simultaneously. This works.
I have two phones, one that supports coded...
Hi,
I tried to enable the CMSIS in my CUSTOM Project but I see the following error and the CMSIS configurator is empty. Please guide what would be the possible problem....
Hardware: nRF52840 DK
SDK: 16.0.0
FreeRTOS: 10.0.0
I am attempting to use UARTE1 for a Modbus port. UART0 is already in use for a Command Line Interface. I can set up...
