dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I have a question regarding the difference between the nRF51822XX AC and nRF51822XX AA during the configuration of IROM and IRAM in Keil software.
I know that...
To the kind attention of Nordic support team,
We are going to use nRF52833 in our products, and we would like to embed in our PC side software (driver) a custom version...
Hi there,
I'm developing a custom board that integrates a NRF52840 based BLE module from Raytac. I was wondering if it is possible to upload the Adafruit nrf52 bootloader...
Hi,
I am implementing LESC on nRF52810 using an example.
Unfortunately, I didn't find any examples.
So, I am programming the PCA10040e with reference to the PCA10040...
Hi,
I am new to NORDIC dev and I find its ppi is really useful but also difficult to understand.
Now my device may be connected the truck engine to count the engine speed...
Hello Team.
I have NRF52840 Development Kit. here is description, what I want to do and How I am doing.
I will send command on terminal and kit will start scanning for...
Hi,
I developed a product using nRF52810 and am now preparing for mass production.
However, since I have no experience in mass production of Bluetooth, I would like...
Hello my current setup use :
nRF52 dev kit
Segger Embedded Studio V4.4
SDK160098a08e2
s132
nRF connect on a iPod touch
I can compile and once connected appreciate...
I am looking for example code on the EV-BT840(832)-V4 dev kit. I can program it with the hex file and it works, but when I program with the nR52 SDK example codes thru Segger...
I am trying Bluetooth mesh light-switch application on microbit, and I have flashed with same light code on multiple microbit devices, Though all the devices are getting detected...
Hi! I am currently writing a DMA driver for UARTE which with the goal of being able to handle large data transmissions with little software intervention as well as handling...
Hi Team,
We are using nRF9160 DK, We tested the asset tracking application with the DK. It is connected to nRF cloud and the data is sent from the DK to cloud. This is...
Hello, I am working on a script on Jlink to be able to flash from my raspberry. I used to have a batch script using nrfjprog and I didn't know how to translate these commands...
Hello!
I have both SD Card and accelerometer in same SPI bus. Both of them working like charm if another is not present. I'am using app_sdcard from 52 sdk.
Can i use spi...
Most of the SDK Peripheral examples support only a single connection.
Is there a guide somewhere which explains and illustrates what, exactly, needs to be changed to update...
