Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi ,
I am using nrf connect 1.2.0 dk. I am now testing the https client example.
However, I always get the connection fail error as belows.
Provisioning certificate...
Hi:
I want to send pictures and voice.So it needs to be faster.What should I do?
I use nrf52832/sdk16.If nrf52840 is used, can it reach 2Mpbs?
Measurement example:nRF5_SDK_16...
Hi there,
Here is what I'm trying to do. I'm trying to use the 52832 as a badge to be used by people in order to report the zone the person is in using a ble mesh network...
HI:
My IC: nRF51822QFAA My SDK Project: ...\nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s110\arm5_no_packs
Appearance：
When I Powerup or...
Hi, I'm having problems flashing the firmware on my Thingy52. I was recently on a course that used another Nordic Semi dev board to connect to the Thingy52 over I2C and use...
Hi. I want to disconect softdevice and ble in order to access to flash memory. I know there are a lot of ways to deal with it. But i want to test to disconect softdevice and...
Good afternoon, Today we had a question about the certification of our product related to the reliability of communication. We received a letter of the following content:...
Hi,
I am trying to update my advertisement data as well as scan response data (i want to put some custom advertisement data and the device name in scan response data). ...
My three buttons are pressed each time, and the LOG information is as follows
0> [00:00:00.000,000] <info> app_timer: RTC: initialized. 0> [00:00:00.000,000] <info> app...
SDK:15.3.0
CHIP:52832
I downloaded sdk15 for nrf52832.all sample programs and soft devices are working fine but boot loader coding is showing some error. I am using this...
Hello,
I am developing the following application:
An nRF52840 bluetooth module connected to a sensor does data acquisition and then sends it directly to an nRF52840...
Hi,
I am trying to use SPIM3 to drive LCD(ili9486), but I have encountered some problems, hoping to give me a solution.
I have 2 questions:
1. spi_config.dcx_pin
How...
Hello, we have run the power profiler on two different example projects, and want to understand the difference between the two.
When we run the blinky project
nRF5_SDK_16...
I am buys setting up a project on the NRF52 that needs to use the TWI. Usually I would read byte for byte, and if one of the registers has enough data to justify it, I would...
