Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi All,
I'm trying to create a hybrid program using the USB CDC ACM example as well as the flash_fstorage example from SDK16. I've been able to get the USB CDC ACM example...
I am using nRF5 SDK 16 on a Rigado BMD-300 (nRF52832) series evaluation kit. The application receives button presses and releases from a peripheral (characteristic change...
Hi, I developed some functions on nf52832, nrf52810 and now I'm with nrf52811. I'm able to put some debug on tx pin so I can read it from PC COM, I use app_uart which use...
The earlier post covers the details of our current project:
https://devzone.nordicsemi.com/f/nordic-q-a/55474/aoa-aod-direction-finding-support-in-nrf52833-sdk-v16-0-0-and...
Hello,
My questions is about ANT and CRC :
Does ANT stack already use a CRC that checks if a data has been received correctly?
Or do I need to create my own when sending...
Hi,
Sometimes our custom board is not readable with the reader uTrust3700 from Identive and it might be related to this post . We are usind SDK 14.2 with our custom board...
I'm using nRF52832 and intend to interface 3 I2C slave devices; the first is the BNO055 IMU.
I've integrated the Bosch "driver" code into my SES project, but I find that...
We are implementing a DFU controller to perform DFU over serial for the nRF52832.
Our reference is the nRF5 SDK v15.3.0 DFU Serial documentation (Nordic/SDK/nRF_SDK_15.3...
There are a few threads on here about this already, but I wasn't find the answer to the exact question I had.
I am using the nRF52832 with SD132 and SDK15.2 on a custom...
I cannot get logging in the Seggar debug terminal nor the J-link viewer application (All terminals) when running this example.
I have the NRF_LOG_BACKEND_RTT_ENABLED selected...
Hello
I am using nrf52840 from nrf9160dk, I am trying to run example from nrf52840 with sdk16.0.0 and sd7.0.0. While checking data on uart I am getting following error...
Hi
I'm trying to get a DFU boot loader working on our own custom hardware. My initial approach was to build secure_bootloader_ble using my own public_key.c file and try...
I updated my Thingy:91 today to version thingy91_fw_2020-04-29_bc7ade8b.
I flashed the mfwnrf9160120, the thingy91_nrf52_connectivity_bridge_2020-04-29_bc7ade8b and the...
Hi, I'm developing firmware for the trf7970a nfc chip. For standard communication the chip uses spi, but a special direct mode uses an additional two wire interface where...
Do the values for current consumption given for the scenarios in Section 5.2.1 of the nRF52833 PS include the current for any peripherals required? E.g. the PS quotes 2.6uA...
