Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I am experimenting with zephyr OS on my nrf52 DK. I want to use the HW AES CCM encryption module available on the board, but I can't figure out how to do this with...
Hallo,
I am developing a custom board, based on Nordic Thingy:91. The custom board won´t support BLE, so the nRF52840 is not intgrated. But Communication with the nRF9160...
Do we have any examples of using tcp in non blocking mode for the NRF9160. I used the USP for PSM example as base for my current project but the blocking call seems to lead...
Hi,
I found some thing not seems to be right in SDK 16. I wonder if this is intentional or a bug. Bluetooth 5 max MTU can be up to 512 bytes. I found the definitions in...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have a use case where peripheral need...
The documentation for ERASEPROTECT.DISABLE states:
The erase protection mechanism can be disabled in order to return a device to factory default settings upon next reset...
Hi All,
I am using nRF52840 chip in one of my battery powered design. As I could see the datasheet and power calculator says the current consumption of nRF is less in...
Sir i am following this link -> https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_app_mqtt_publisher.html
and I have one...
Hi! I'm using the fatfs library to read/write data from/to an SD-card. I noticed the following behaviour:
When I try to write or read data directly after receiving a BLE...
Hi All,
I am using nRF52840 in one of our design. As the P0.18 is the RESET pin, it is tough to route the trace without a pad on via. Hence as I have modified my design...
Hi Friend,
My platform is SDK 16 with S140 softdevice.
I set a gpio for edge trigger interrupt. But I cannot get the correct gpio state if the data pulse is too short...
Hello,
I want to test bluetooth on nRF9160DK. How to do that? I programmed nRF52 on nRF9160DK with hci uart sample and board selected is nrf52840_pca10090.
But how to...
I'm currently trying to add SUPL support to our existing product, and I'm finding that the SUPL library is absolutely huge. Enabling CONFIG_SUPL_CLIENT_LIB appears to add...
Was wondering if anyone knew why this fault might be triggered?
It triggers when I try to use SPI0 and LTE together.
AT host is disabled.
The code stops here during...
While trying to utilize the TEMP peripheral today, I found that after the event handler returns a single reading the application does not continue to run. Any actions that...
