Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello guys. I have six of these boards nrf52840
Do you have any Arduino Bluetooth sample code for using six or seven of these boards in a peer to peer network setup? ...
Hi , i have implemented a event to flash handler with NRF_SDH_SOC_OBSERVER and it work . But I need to know which operation is related to the event , Es: void FlashEvent_Handler...
I am trying to open HTTPS client project from \v1.2.0\nrf\samples\nrf9160\https_client i am facing below error.
I tried opening different project still i am getting same...
Hi,
I followed this thread ( Link ) to implement a simple message model on the light switch example from nRF SDK for Mesh v1.0.1. I created a "send_simple_message" function...
Hi,
Our custom NRF52840 device uses a cellular modem. We communicate with this modem using AT commands.
We will also be hooking up our devices to a custom server that...
Hello,
I have recently purchased an nrf9160-DK for a project I'm working on here in the UK. Having fired it up and realised that the iBasis coverage is minimal where can...
I'm starting to try to figure out a secure OTA process using the 9160 and tools that Nordic has provided in the SDK and I am confused by one thing I'm encountering.
What...
Hi.
I want to test my iBasis SIM card for NB-IoT with nRF9160DK. So, I tested with the "AT_client" example. I have followed "Getting Start with nRF8160 DK" instruction and...
Hi, I am trying to run ble example - uart in segger embedded studio. I am using 11.0 sdk. I have imported keil project into segger embedded studio. I have the error stating...
Hi devzone,
I'm using translation.
I use nRF52840. I created a firmware like the attached one based on the SDK15.3\examples\peripheral\bie_peripheral\ble_app_blinky. ...
Hi all,
I have a custom board with LED on PIN 11 of nRF52832, and I am using SWD P20 configuration to program my board through nrf52 DK PCA10040. Apparently, nRFgo Studio...
Hi
this is not a question - I'd like to give feedback about the peripheral example usbd_hid_generic.
I'm new to 52840 and new to USB. As learning lesson I tried to build...
Hi All
I am now developing BLE application on nRF52840 DK. I have a question about BLE retransmission process.
When master sends a packet to initiate a connection event...
Hello All,
When I was testing our ble keyboard, there was a problem with the Lenovo tablet connection pairing binding. Please help me, thank you!
1. Ble keyboard is based...
