Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
What is exact difference between heartbeat and health models?
I know heartbeat can be used to detect node outage, but so can be health message?
So, which one should be...
When starting up the device with the nRF5 SDK 3.2.0 for mesh, even though the model and subscription list state is loaded from flash, it is stored again right afterwards....
To the kind attention of Nordic support team,
I was reading this blog https://www.ericsson.com/en/blog/2017/12/wake-up-radio--a-key-component-of-iot
May I ask if Nordic...
After Downgrade protection in the NRF9160 has been set with AT%XPRODDONE=1, switching it off with AT %XPRODDONE=0 returns ERROR. Is there a way to disable downgrade protection...
Hello DevZone,
Is there a way for hardware to update the timer capture register?
I want to create different frequencies using a single timer. Next to the timer, Bluetooth...
I am using Nordic proprietary RF receiver and transmitter. I want to display the received data on my serial terminal using UART pins (any 2 pins as Rx-Tx) .
When I tried...
Hello,
i'm writing a code for NRF9160DK where i plan to send a HTTP POST request to a test server when i push BUTTON1 on DK. To achieve this result i studied separately...
Hello,
I have an issue since today. Indeed I worked for a few weeks on the nRF52840 and everything was alright. I used a dock to connect the nRF52840 by serial port with...
Hi,
I have an application where an nRF52840 DK(1.1.0) is configured to work as both central and peripheral. I want to set a lesser duration for advertising with whitelisting...
I have added lbs_service from ble_app_blinky service within ble_app_glucose example. I made changes in main.c and EMPROJECT File accordingly. I have added ble_lbs.c file in...
I need help in implementing Monitor Mode Debugging (MMD) using Segger Embedded Studio development. Can you please provide detailed help and explanation please?
Hi Devzone:
After searching through the forum I found out that nrf_fstorage_write can only make 1 to 0. So each write needs an erase operation preceding it.
But erase...
Baseline: CLI example on the 52832 with SDK v15.3
I assume the issue will be some more undocumented fix.
sdk_config.h
main.c from the CLI example (UART backend...
I was previously working on nRF51822 ble beacon, in which codes flash of hex 20006.
But i wanted to flash a code nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\experimental_ble_app_blinky...
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
