Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Central and peripheral is pairing and bonded. Central scanning with whitelist, if Slave is not online, master scan with whitelist will enter error when more than 30 seconds...
I'm using whitelist when bonded, but I want delete bonded then connect to anther device,.
But when scan again, whitelist_load is error. Try delete whitelist at the same...
Extended corruption occurs if DMA transfers for commands and data originate from the same RAM bank.
It is avoided if transfer of command bytes and transfer of data bytes...
Hello,
I ran into this list recently: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52840%2FCOMP%2Fnrf52840%2FnRF52840_ic_rev_sdk_sd_comp_matrix.html...
Hi,
I'm using two nrf52840 Dev Kits and am trying to test out the ATT_MTU throughput example with SDKv16. Whenever I program one of my boards I get repeated fatal error...
I am pulling my hair, literally , I just can't get this company !
I am working with 4 IDE's in parallel and none of them has this stupidity .
I right click->add a new...
Background
I intend to use an nrf52 based board in remote inaccessible locations. It is important that I can always recover from a problem. As such, I want to use the watchdog...
Hi，
In the 07-5123-07-zigbee-cluster-library-specification specification, I see clusters that support CO2 and HCHO, but I did not see any definitions of CO2 and HCHO (cluster...
Hi,
I'm working with NRF52832 which operates on battery in low-power mode.
The unit samples and transmit data (via modem) 2 times a day.
After few weeks / months of...
I have written a UART driver that is intended to receive data in a continuous stream. I know it basically works as it is able to communicate with an external device at 115...
Hi Nordic team,
I have a simple HID BLE device which send volume+/- multimedia keys to a Android device, it works
well if it is first time to pair with the Android device...
I'm developing a project that use BLE advertise and uart communication with other uC.
The uart part is based on libuarte example. To decrease the current consumption, I...
I am trying to do spp communication between central and peripheral with BLE.
First, the peripheral uses microchip RN4871.
The BLE setting is Service UUID: 49535343FE7D4AE58FA99FAFD205E455...
