if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
I am trying to connect to another type of board via the UART on the development kit. However, there seems to be a voltage mismatch. Are the nRF52840 development kit UART signals...
hi... i want to store data in flash , i will get the data periodically . i have merged the ble_app_uart +fstorage example . Even i am writing data to flash using write command...
Hi everyone, I have a question related to the power supply of nRF52840 DK
I want to operate the nRF52840 DK with a LiPo battery (for experimental purposes). Is it possible...
The antenna is mechanically symmetric, but as I understand not electrically symmetric.
Is this an errror ?
www.fractusantennas.com/.../UM_FR01-S4-210.pdf
Chapter 5:...
I am wondering what happens to the NRF LOG statements when not running in the debugger.
I have found (probably due to interaction with the SoftDevice) that too much NRF_DEBUG...
I cannot get the scope of the sdk_config.h file to encompass all modules. Process
Start with example project using the file system as per the install.
After compiling...
I would like to use the UART at the lowest possible level and Ihave created a very simple example which uses the UART bus with the registers. The example should write word...
Radio is flashing green, on and off, but I can't seem to connect to it. Looking at the graph of usage, I can see that it is talking to something since the available amount...
Hi,
I'm using pc-ble-driver-py.
I bought the nrf52832 dongle.
The problem is uart pin number of dongle.
The pins of my dongle and the pins of the hex file are different...
I am working on adding firmware updates to my BLE application on the BL652 module ( nRF52832/PCA10040 ). nRF 15.2.
I added in the code for the BLE Background DFU, which...
Hi ,
I can not understand or there is something wrong in this example here ;
He defined " point_fifo" but initialized "my_fifo" , How does this work ?
https://infocenter...
We want to qualify a product with nrf52832 and preferable S132 6.1.1. When we tried to use QDID 125047 there were inconsistency problems in Launch Studio, table 1a was not...
Can i configure more than one pin for wake up the microcontroler from deep sleep ? like this: nrf_gpio_cfg_sense_input(30, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_LOW); nrf_gpio_cfg_sense_input...
What is the receive buffer size for IP packet data, i.e. how many bytes of data can the modem receive (in one or several UDP packets) before I call recv() or recvfrom() on...
Hi Sir,
For test the nRF9160 GPS, based on the nRF connect v1.2.0.
Do we have the GPS API for cold/warm/hot start?
And which example code we can reference?
Thank you...
