Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hello,
lately i've not been able to connect to NB-IoT network as i did before.
Long story short:
I'm working with nrf9160 since 3 months and i have been able to connect...
When the macro NRF_SDH_BLE_GATT_MAX_MTU_SIZE is changed in the sdk_config.h file of any example from the ble_peripheral folder, the slave sends the message Exchange MTU Request...
Hi,
I am using nrf mesh sdk 3.1.0. with nrf52832.
For iv update one condition is iv_timeout_limit_passed(m_net_state.iv_update.timeout_counter). The timeout_counter value...
Hi,
I am evaluating ble peripheral with nRF52840 SDK 16 and SoftDevice s140 on windows 10.
The SDK is copied at location: C:\Nordic_Semi\nRF5SDK160098a08e2\
The SoftDEvice...
Hello,
I am not able to connect the dots. After setting up the beacons, ( adopted ble_beacon_app from Sdk 16 ) how can I perform localization algorithm ( trilateration)...
Hello. I try to configure radio at NRF52811 to prepare antenna switching and get correct I/Q samples from different antennas. I have 2 antennas that are 6 cm apart from one...
hello, I try to make an application with 6 different services. I used the ble_custom_service tutorial to create my different services.
I manage to work without problems...
Hi,
I am working with the bsp.c functions. One of the actions is BSP_BUTTON_ACTION_PUSH, which the value is 1. I would like to know at which electrical signal it is related...
Hello All, I am having a trouble with the nReset Pin during Deep Sleep. The issue is that the board is waking up from Deep Sleep due to floating nReset Pin. I am using a nrf52480...
Hi,
I am currently working on a product based on an nRF52832 (SDK 15.3, S112 6.1).
The firmware uses the Nordic UART Service to receive and send data from and to a smartphone...
I'm working on a new nRF5340 project where this will be the main application processor. The target system will support a large variety of sensors, and we expect to use a very...
Dear All,
We have designed our custom board based on BMD-330 (nRF52810 chipset). It uses i2c (TWI) to communicate with Azoteq IQS620A sensor .
TWI code runs fine on nRF52...
Hello there. I have few questions about nrf9160 GNSS part. Seems NRF have implemented own GPS L1 C/A correlator, current quality is not impressive at this moment, but approach...
Hello
In the radio test we can set up to 80 channels.
But isn't the table for the channel as follows?
40 channels is 2480MHz, right? What is the frequency of 80...
