Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
I need to store some data into the NVM of nRF52832 , which can be saved after powering down . In nRF5_SDK_16.0.0_98a08e2 , which example should I learn ?
All examples of...
Now I can only download the 《nRF52832 product brief.pdf》 . The link is shown below:
www.nordicsemi.com/.../Getting-started
However , this data sheet is not complete ....
Hi,
I'm using an MS50SF1 nrf52832 3rd party module. I successfully programmed it through nrf52 DK.
After program that module, I was able view it through nRF Mesh App ...
Is it possible to update from 6.1.1
To 7.0.1?
New softdevice does not fit if linker file FLASH address starts at 0x26000, that's why increase to 0x27000. ...
We are using UART peripheral from nrf52840. It communicates with a modem over the serial, but after receiving a random number of bytes, we get frame errors(the uart driver...
I am working on a custom board with the nRF9160 SiP. It comes with pre-programmed modem firmware. Header pins for UART1 and UART2 are provided on the custom board. Is it possible...
This is a strange one. I had a custom PCB that included an MDBT42Q module. After I learned how to program it, it worked fine. I made a slight revision to the PCB, and this...
I'm implementing a function which enters sleep mode and wakes up by interrupt like below..
Is this correct way to enter sleep mode? Do you know any other better ways...
Window10 nrf tag: 1.2.0 SES v4.4.2a
I'm attempting to code a one-shot mqtt function, but it fails in v1.2.0 whiile it succeeded in v1.1.0. I coded the below main.c by modifying...
Hello ,
I was working on BLE mesh implementation, It would be helpful if there is information regarding current consumption of different mesh nodes ( low power node, friend...
Dear team:
1.So how can I increase transmission withou improving TX power As for the transmission distance of nRF52832, apart from improving the TX power, what is the better...
Hello,
There is a particular task I'd like to accomplish, and I have been looking into the nRF52840 to do it. In a nutshell, I want to build a bi-directional relay for USB...
Hi,
i downloaded new SDK14 with example, after i upload hex from example in ble_peripheral/ble_app_hrs
I use s132 / nrf52
program stuck here :
ret_code_t nrf_sdh_enable_request...
Linker script `nrf_common.ld` in nRF5 SDK v16 defines __etext to point to the end of the .text section. It needs to be 4-byte aligned according to comments in `gcc_startup_xxxx...
