Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
How to configure the start address and size of flash memory and nrf52832 in SES and how to calculate the size? How to calculate the start address and size of app and bootloader...
Hi,
Current Status:
I'm trying to run the fpu_fft example from the SDK 15.3.0 on my nRF52832 DevKit. When I clean and build the project in SES everything is fine and I...
Hi, I have a question about unknown flash data from MBR area which start from offset 0x0000035C, 20 bytes data show as below.
Data[20] : FF FF FF FF FF FF FF FF FF FF FF...
There doesn't seem to be any validation of the image when updating the bootloader by secure DFU. nrfutil has no switch to generate any crc or ecdsa_signature. The code uses...
Hi
I am making mesh network using Raspberry pi and NRF52 DK. I install bluez 5 and meshctl on raspberry pi. I successfully connected nrf52 dk using bluetooth. I attached...
I am doing this nRF52xx-to-Thingy-52 example: https://github.com/crfosse/Thingy-52-to-nRF52xx I am able to get the led part working fine, but when I finish the instructions...
I am trying to merge Softdevice, bootloader, bootloader setting and application. But unable to do in a single mergehex command. If i do merge seperately ((BL + SD + APP) with...
Hello.
This function from Zigbee SDK 4.0.0 changes configuration of already configured input pin by calling nrf_gpio_cfg_default(ERASE_PIN);
The leds_buttons_init()...
I loaded up pca10056e ble_app_beacon example for SES to test it on a custom nrf52811 device I have built (using BMD-360 module).
I followed the instructions here and removed...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I want to know the life of FLASH by garbage collection. Assume that garbage collection is performed only when "PM_EVT_STORAGE_FULL...
the python package is not updated through pip with last release of SD_API and corresponding hex files.
I know that you give instruction to build driver but it could be easier...
I am trying to test a simple non-connectable BLE adverstising. I am using the following resources.
1. SDK - 16.0
2. SD - S132
3. Board - NRF52 Development kit.
4....
hardware: nRF9160 DK 0.8.2 firmware: 0.7.0-29.alpha
I want to send data every a few seconds through MQTT. It fails in the first and second Tx after MQTT client initiation...
