We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I have nRF Connect v4.19.2 installed on a Samsung Note 8.0 (Android Tablet)
I have several BBC Micro:bits and I can get their Serial Numbers by three different methods:...
Hello,
We are leveraging the Android BLE Library from Nordic available on GitHub (release v2.1.1).
In a scenario where there are repeated requests to connect as a result...
Hi,
I have an issue about writing and reading data using flash area of nrf9160. I'm using the library of pynrfjprog and the following script for writing/reading data.
...
Hi,
I've used the ADXL362 sensor sample code in the zephyr folder to get the low power accelerometer sensor working on the the thingy91. It triggers on motion and I can...
Hi Nordic Team:
Our important customer develop ANT+ products.They will use zephyr RTOS to develop ANT+ products.But ,they can not find any example project,in the zephyr...
Hi, I want to transfer the firmware to 52832 and enter the bootloader mode successfully. and the I send {0x02,00,00},it can't not enter the case of on_packet_received: SERIAL_DFU_OP_CODE_SET_RECEIPT_NOTIF...
Hi All,
I am developing a data acquisition system in which my device generates an interrupt for every 5ms upon its data is ready. I store one second long data in local buffer...
hi,
We have a product in production but the PCB-A had been updated with new functionality.
We want to make sure old f/w is not inadvertently loaded to new h/w.
To do...
We would like to develop OTA firmware update with nRF52840.
In the development phase, we have been using "Thingy: 91" and place the firmware onto the MCUs of nRF9160 and...
Hi all, I'm developing nRF52832.
My goal is to send ADC data to central device using BLE.
Below is part of my code.
Maximum MTU size is 251.
I sent data in 16...
Hello,
nRF52-DK (PCA10040) has two mysterious 12 pF capacitors C52 and C53 connected to P0.25 and P0.26 respectively (see attached picture).
Is there any special purpose...
I'm using nRF52DK with ble_app_hids_mouse to pair with the smartphone.
From the smartphone we can disconnect the device at will. But I have problem when I want the device...
Hi All,
Looks like develop nRF52840 on SDK16.0 required
NordicSemiconductor.nRF_DeviceFamilyPack.8.27.0.pack
But there is no such pack on http://developer...
Dear All, I am trying to measure the current consumption for the nRF52840 USB Dongle. I intend to use it as a beaconing device and attach it to a battery.
At the moment...
