Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
We're developing a product based on Zephyr for the NRF52840 (currently seems to be Zephyr 1.13 OpenSource variant). When doing power measurements, it seems that the...
nRF Sniffer is capturing packets, but I see no device names in the Devices List, and I cannot sniff a paring procedure.
The source address in the Devices List also do not...
I'm using the NRF9160DK, the asset_tracker example works fine over Cat-M together with the iBasis sim.
I want to run my applications on NB-IoT, so I'm trying to connect...
Hi,
I have an issue of watchdog in my application.
I think it may occur due to an interrupt (NFC trigger), which calls the function xTaskGetTickCount () instead of...
Hi community ! I saw a lot of subject about "Mesh throughput" which was outdated and i still have questions. I'm using nRF52840 DK with nRF5 SDK for Mesh v4.0.0
1) Does...
Hi,
I'm using nRF Connect to connect to the secure bootloader. In the debug log I see that an MTU of 185 is requested and 183 is replied. I also see this in the Wireshark...
When I used nrf52840 to connect the peripherals with pc-ble-driver-py, I had my own custom UUID, so I needed to add a custom UUID. I referred to this article , but the following...
Hi,
I know that there are different ways to set up the radio, but generally speaking, is there a general practice for how commercial devices' PHYs are set up when advertising...
Hello people, Honestly this is a problem more related to a Raspberry Pi than the nRF52832 but I'm getting same difficulties here so I will explain my situation. I have been...
Hi
I just want to read the Device Information Firmware revision string from a known Peripheral on my Central.
I Use the PCA10028 with SDK 12.3 and Softdevice S130...
Hello to all,
i've developed some application under 3.2.0 SDK. Now I want to port my application on new 4.1.0 SDK but a I have found a relevant issue.
Before migrating...
In section 6.3.2 of the NRF52840 dongle user guide it describes how to modify the board for use with an external, regulated power supply. Once those modifications are made...
In order to implement the central roll, I put ble_app_uart_c on ble_app_multilink_central and joined them to communicate with the pc.
What I did
1. Add enable in ble_app_uart_c...
Hi ,
I need to start my application using sdk5 16.0 version, which should have custom ble servivnced and dfu feature.
After getting some trouble with zephyr os, i decided...
I have used an example in the sdk 15.2.0 Pin_change_int_pca10040 and added 2 header files and 2 C files extra to this project. I have cleared all the error which came while...
