Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hello all,
I am working on nRF52840 EVM board.
I am not changing any thing in nRF52840 EVM board.
I was using nRF52840 board for downloading firmware in external custom...
I'm trying to use an MMA8652FC accelerometer with the nRF52832. When I call the function nrf_drv_twi_tx() the board hard faults, stopping in <SDK>\components\libraries\util...
In the case that I used custom board, I used bootloader_secure to OTA; but after OTA, the program doesn't jump to the application, even app nrf connect notify Sent Successfully...
Dear Community;
I am running some current measurements on the NRF9160 DK. I am following the manual instructions:
1.-I am powering the NRF through external power supply...
Aim: transfer large data coming from UART to nRF52832 over BLE 5.0 as fast as possible. Want to use 921600 baud rate in the case given below.
Scenario:
SDK: 15.2.0 ...
I have created an out of tree board folder following the same pattern as the Nordic PCA10090 and that is working as expected. What I would like to do now is have 2 versions...
nrf52832 sdk16.0
my program initialize as below：
advertising_init(m_advertising_data_init_array,10);
adv_scan_start(erase_bonds);
scan and advertising is ok，but when...
Cannot connect to ATECC508A through TWI with NRF52832. Tested with nRF5_SDK_12 twi_master and deprecated twi_sw_master. It was working fine only with NRF51822 nRF5_SDK_12...
Hi,
we would like to use a production ready open source RTOS with our nrf52840 development under Linux (with eclipse or visual studio code).
We have tried with mbed...
I am using nrfmesh android app. I have configured a mesh network. exported network. then reinstalled app and connect to network. then tried to read state of device, then get...
A mesh node contains multiple lights.
Assume a light contains 5 Elements (Main, Temperature, Hue, Saturation, Light LC). Each light has 30 model servers implemented.
When...
Hi,
I am trying to test ble_app_blinky app. I am using VS Code for the development IDE and while compiling the application using MAKE I am running into Cannot file Source...
We are seeing about 500 uA in sleep mode and we expect to see under 2 uA. We are using an nRF52810 on a BMD-330 module on SDK 16.0.0.
Here's the relevant code...
nrf_pwr_mgmt_run...
Hello all!
How can I get the current count of a timer without stopping it?
Right now I'm doing like this:
_timer_base->TASKS_CAPTURE[channel] = 1; uint32_t counter...
Hi,
I am no programmer, but I wanted to try the Wake-on-NFC example on the 52840 dongle (I soldered an NFC flex on pins P0.09 and P0.10). I have downloaded SES and nRF SDK...
