According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
in sdk16 "examples\peripheral\usbd_hid_composite" example, i found that after those code
ret = nrf_drv_clock_init(); APP_ERROR_CHECK(ret);
nrf_drv_clock_lfclk_request...
Hi,
I want to set advertising name in the main.c.
err = bt_set_name("NAME test"); if (err) { printk("BLE set name error (err %d)\n", err); }else{ printk("BLE set name...
Hello Nordic,
I had some questions regarding the management of versions of various components during application development (nRF Connect SDK/9160 Modem Firmware/Modem Certifications...
1. I am using a boost to power the USBD since I am using coin cell to power the whole system, what minimum and maximum supply current is needed/can be handled?
2. What boost...
I have being confused by other post around DevZone about DS18B20 to integrate with nRF BLE application or rather programmatic aspect is concerned . Is DS18B20 suitable for...
Hi!
I've just received a nRF9160 DK.
I've installed nRF Connect v2.6.2 and LTE Link Monitor.
I select the device (3 serial ports are shown). I press reset button and...
When working with a custom board with nRF52840 chip, I'm having serious problems with SWD connectivity. In many cases JLinkExe can't connect to target at all. I did some measurements...
Hi there!
I'm trying to simulate a peripheral with a PCA10040 and nRF Connect for Desktop.
I've made the Server Setup, applied to the board and started advertising - everything...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Initially I was in assumption that once...
Hi,
Is there a table / .xls available for ALL nordic parts to date?
I'm trying to find all options with +8 dBm TX Power & WLCSP package. (no need for usb)
Hi, I'm trying to get the nrf_stack_guard and nrf_mpu libraries to catch writes past the end of the stack. My stack is 8kB in size (0x2000E000-0x20010000). This is the log...
Hi,
I'm working on the custom board using nrf52832 chip and have performed the secure bootloader using ble on the custom board.
I have made these changes so far on the...
We want to connect provisioned node to multiple mobile application over same mash network (Note: We are trying to give access to multiple user(using multiple mobile) to connect...
