I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello,
I've been trying to figure out if this board with STM32F103 ( www.aliexpress.com/.../2042650923.html
can directly plug into my debug board
( www.aliexpress...
All,
We are in product on a product using the nRF52832 and are noticing in manufacturing that we aren't able to make it through the self test part of fab because of shoddy...
I need to understand how a multi-link configuration can achieve real-time transmission - its all about latency.
The Application
In my nRF52840 application I have several...
Hello,
I am using a custom bootloader. The bootloader does not contain dfu, it will just check the new image, program the new image, then jump to it.
I cannot jump to...
Hi,
I want my characteristic to have a different UUID than its service on my server:
I followed the leads from the post below:
https://devzone.nordicsemi.com/f...
Hi there
I was following all the steps on Building the mesh stack and examples , Building with SEGGER Embedded Studio and nRF5 SDK for Mesh Segger Embedded Studio first...
Hello
My understanding is that the only way a mobile phone can communicate with a mesh network is through the GATT bearer..
Im trying to figure out why its not possible...
Im using two nrf51822 as severs and one nrf52DK as a client in mesh light-switch examples. So i need to implement mesh dfu on server side( on nrf51822) . How to do this ....
Dear Support,
Installed the new Mesh SDK v2.1.0 and tried to build the sample solutions with SES.
Unfortunately I am always getting the following error:
build/serial_nrf52832_xxAA_s132_6...
I would like to use both UARTs.
I'm trying to run the given example with SDK patch from https://devzone.nordicsemi.com/f/nordic-q-a/25173/nrf52840-uart1-not-working-in-sdk...
Goodmornig,
I can't compiling the example project ! Do you knows the reason ?
Error ( imagw1 ): C:\Users\utente\Desktop\pc-nrfconnect-rssi-master\fw\src\rssi_uart\sdk...
Hello everyone, I'm trying to run my nrf51 with ADS1298 using SPI. nrf51 is master and ADS1298 is slave.
I configured SPI as
const nrf_drv_spi_config_t spi_config =...
Hi,
I'm trying to implement GPIOs in Mesh 2.0 light switch example and I'm using SDK 15.0. I'm getting undefined reference errors and I know that I have to add legacy GPIOTE...
Hello guys.
I'm new with nodic nRF52 SDK and I tried to enable debug by setting 1 on "NRF_LOG_ENABLED" in sdk_config.h, but nothing happens in com port criated by Jtag...
