Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
How to write a byte in flash by using
static void flash_word_write(uint32_t * p_address, uint32_t value) function
while in a advertising mode.
I tried to call the...
Hello.
Here is my conditations;
using ukeil 5.
sd132 Version 5.
sdk version 14,2,17b948a
In my project, i am using secure connection. So peer manager...
Hello Guys,
I am newbie to nrf51822 programming. Currently using nrf51822 (raytac's MDBT40) with S130, SDK11.
I am programming the nrf51822 using arduino IDE using this...
Hi,
I'm seeing this error PM_EVT_PEER_DATA_UPDATE_FAILED sometimes and I need to understand what are the options on handling this error except for just asserting it. I...
Hi,
We have to implement a nRF to nRF DFU. On the nRF51 side a have an external memory with two bankers to perform secure update and downgrade using a bank 2. Now, we are...
when scan the BLE device, screen can look the device's name, but the time parameter is means?
ex:
-31 dbm <-> 1010ms
1010ms means? is about dbm power value>
thks...
We have field reports of BlackBerry Priv not being able to "connect" to our nRF52 based hardware.
BlackBerry Priv is: www.gsmarena.com/blackberry_priv-7587.php
(Runs...
I use same SDK to program the 1.nRF52_DK borad (on broad chip 52832) ,and 2.external program borad chip 52832.
Have a issue, 1.nRF52_DK borad is success to advertisement...
Hey!
Using osx, SES 3.30, importing experimental_ble_app_blinky example from nRF5_SDK_11.0.0_89a8197 to be used with NRF51822 chip. When importing I chose pca10028/s130/iar...
Hello
I am testing with the lis2dh12 sensor and our custom board. I made the LCD test successfully. So I tested the lis2dh12 sensor based on the LCD code, but it failed....
Is there a comprehensive explanation of the usage of uuids_complete, uuids_more_available & uuids_solicited when to use them and how the stack behaves/uses them. I getting...
Hello
First of all, I would like to apologize if a similar question was already asked but all this BLE matter is so broad that it defeats me.
I am planning to put two...
I try to use Eclipse for my nrf project. Previously I used Keil but now, I should to use Eclipse. Anyway, I can build nordic sdk example project but when I work with main...
Hi,
I have posted the same question in the following URL.
devzone.nordicsemi.com/.../
It will be very helpful if you tell me how to get a correct MIC result by AES...
