Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi
I want to make a dongle which can connect to and communicate with HID .if the peripheral is a HID(eg gamepad ,consumer or mouse ),the central device how to communicate...
Hi,
This is just a quick check of my understanding of the interrupt priority levels on nRF51. I read up on the documentation I can find.
I'm assuming that I will receive...
Hi,
I am designing a custom PCB with the nRF52832, I am going to use wire bent antenna over it. Can I bend feed wire by 45 degree. I have attached image for the part I am...
Hi All
I am using the example of uart in SDK10 wit nordic 51822
First of all ,I add a PA with 51822 to increase the signal of BLE, but I notice that the speed of PA is...
I can read peer address and rssi field in the scan request report. But how can I read the AdvA address field in the scan request to make sure that the scan request packet...
Is there a method to remove a node from the network using the current bt mesh stack? I've looked through device_state_manager.c but it appears to me that there are only functions...
Hi,
I am using 2 nRF52840 DK to build a network, One is the client and the other one is the server. Both of them are connected to computer with USB cable.
I would like...
hi,
i test my project for i2c sensor module, the debug found have error what there are the following error tips.
..\..\..\swct_application\i2c_sensor_driver.c(14): error...
Hi,
I'm trying to write custom boot loader, that receiving hex file via uart and write it to location 0x40000 and then jumps to the location. I changed FLASH_ADDRESS and...
Dear experts,
We are evaluating to perform Round Trip Time (RTT) measurement for ranging application. The accuracy requirement is 1m to 2m. Are there any sample applications...
Hi,
I am using a custom board which I designed based on the Puck-js board, except that I am only using an I2C based distance sensor instead of the other devices onboard...
After experiencing UART problems without handshaking I opted to enable hardware handshaking.
Where RTS & CTS are pins 5 & 7 respectively.
I was experiencing overrun (insufficient...
The nRF6905 nRFready Basic Remote is a complete hardware and software reference design for basic 2.4GHz RF remote controls.
What nRF24LE1 devices are included in the hardware...
hi sit and test bluetooth mesh and i do not quite understand how the client knows that the server is off or on and there is a way to find out if a server is on or off
Hello,
I would like to use nRF52840 in order to make some BLE5.0 mesh products. When I open the nrF5 for mesh, I can see only examples for nRF52832.
Do you know if these...
