Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi, I am have been using PPI to control SPI transfer in response to a GPIO interrupt.
The PPI initiated SPI transfer that reads an external device's register A and I would...
while the ble_uart example is a great resource of information, i have a need to completely separate the ble nus data in / out from the hw uart code
using sdk 14.2.0
...
Hi everyone,
So I've this arduino code that utilizes the I2C library and made some convertions to it to work with the nrf52832 in the segger embedded studio and when debugging...
Hello, I'm trying to migrate an Atmel project to nrf51822 chip.
Now, in the original project there were 2 CB arrays registered, one dealing iwth GATT one with GAP:
a...
hi,
I am working on nrf51822 chip and using sdk11.0.0 sdk,softdevice (s130 2.0.1) .I want to send 4Kb of data in a packet from the central device and on the other side my...
Dear all,
We have just purchased "nRF52840 Preview DK" kit for a project that connects BLE SoC to Linux host machine.
I have just realized that Connectivty example from...
Hi,
I managed to get fds to store some information in nrf51dk for persistent data storage. I would like to check if the data is still available in the chip after power...
Well, I have question for this SPI connection problem.
anyway,I have nRF51822 core board using adxl345 with SPI connection. that connect SDA to P5, SDO to P6, SCL to P7,...
Hello,
I understand the nRF9E5 is programmed through the externally attached AT25320B, ok. I understand three bytes are appended to the .hex file for the 8051. Since I...
Hello Nordic team,
I just post a message here to take the temperature, and your respective engineering opinions about that…
It's been a few months that I work on the...
I'm using SDK 14.2 (not really relevant I guess) on an nRF52832. The application requires a greeting to be sent to the remote through NUS as soon as a connection is made....
Hi there,
I was trying to use S110 to implement my project but found there is no more release for that after SDK 8 and I have concerns on bug fixes won't be merged back...
Hi,
I'm wondering if CSI is available on nRF chips. It can be used for advanced sensing purpose. There have been tons of works on WiFi sensing through CSI. Is it by any...
hi,
i use SPIM0 transfer data, stoping SPIM0 and then disabling SPIM0 when the data is transfed,but the device consume current is 500uA, if i use SPI0 transfer data,call...
