Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
I am using two nRF5340 Audio DKs one as a gateway and the other as a headset. I tested the nrf5340_audio example and managed to get the speaker output working through the...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic,
I want to implement a LED blinking like below pseudo code. I'd like to use PWM sequence Timer x n , GPIOTE, PPI since it doesn't consume any CPU time. for ...
The functions “ nrf_log_frontend_std_...() ” called by “ NRF_LOG_INTERNAL_MODULE(...) ” use only 4-byte (uint32_t) arguments, which is not suitable for arguments of type ...
Hello
I want to clarify something because there seems to be a lot of conflicting information on Dev Zone, and the nRF5340 DK documentation doesn't specify the following...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
Hi,
I am trying the system_off sample of Zephyr version 4.0.99: https://docs.zephyrproject.org/latest/samples/boards/nordic/system_off/README.html
The sample works...
Hi,
I have a problem with nRF52832 after entering the radio RX state. I use a proprietary protocol with fixed packet length. Packet transmission works fine, receiving the...
Hi, We developed our custom BLE electronic board based on the nRF54L15 SoC. On this project the nRF54L15 firmware setup a SPI slave interface in order to receive commands...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
HI
I am developing an LCD using the GC9A01 module. I implemented it by referring to the code as below and it works fine.
https://github.com/Exboom/GC9A01_nRF52
But...
Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
