Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
im using keil5 for this .i getting problem or may be confusion while selecting the packages .also could i use the softdevice for this .Also wanted to know the uart...
I want use two 52DK for BLE transfer demo, one 52DK download nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart",
other 52DK download "nRF5_SDK_15.0.0_a53641a...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device. Schematics are shown below
here BATTERY is connected...
The nordic thingy won't program anymore every time I try to program it gives an unknown error.
Does this mean that it is bricked and i need to change the chip or is there...
hi,
I am trying to develope a code to blink 2 LED's for different time interval of 500mS and 800mS using TIMER but I want to control them using TIMER 0 for one LED and TIMER...
Good afternoon,
I would like to ask you if it is actually possible for the peripheral device to automatically repair with the central device after being powered off through...
Hi All,
I have an application successfully running on nrf52832 with sd132 which I am migrating to nrf52810 sd112. Unfortunately since the softdevice structure has changed...
I am using nrf52832_xxaa and I'm porting my device from SDK11 to 14.
#define APP_SOC_OBSERVER_PRIO 1 /// Applications' SoC observer priority. #define APP_BLE_OBSERVER_PRIO...
Hello guys,
I have got some evaluation project based on Mesh.
I have got Mesh SDK (nrf52832 DK Based) and Thingy52 Mesh examples working. Even we created sample Android...
How is the output power effected by temperature on the nRF52832 chip? Is there any data or documentation specifying the change in output power vs low and high temps?
Hi,
I use the bootloader example given into the library to update my application (or bootloader and/or softdevice+bootloader) via DFU but I don't find in this code how to...
Hello,
I have questions on the Provisioner of a network. Reading through the documentation on Mesh Provisioning, I have come to understand that some amount of data has...
I've tried this but it does not work: static void adv_slots_init(void)
{
uint8_t default_frame_data[] = {0x03,0x03,0xAA, 0xFE,0x13,0x16,0xAA, 0xFE,0x10, 0xF8,0x03,'g','o...
on the nrf52832 I am configuring pin 10 as an input. There is either 0 or 3.1V on the pin depending on whether a charger is connected to the board.
When I read the state...
