Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
hi team, i want to edit my uuid, major and minor. i searching for the example. i am using nrf52840. i didnt get any example. but there is a example for nrf51 ble_app_beacon_bcs...
infocenter.nordicsemi.com/.../nwp_015.pdf
Above refered white paper says:
"refer to the Nordic Semiconductor white paper ‘nRF TX measurements’ for procedures on how to...
Is it possible to set two nRF52 as duplex MODEM?
The objective is to monitor a remote solar powered device from a PC. There would be one nRF52 device at each end (one at...
Does anyone know of any nRF52832 devices designed for use as a key fob?
The Thingy52 looks great but it's a little big and I don't need all of those sensors. Also, I'd...
Hello Everyone,
I am trying to run examples of BLE Pheripheral in my NRF51822 board but something is wrong. SoftDevice and algorithm are downloading well but bluetooth is...
I'm trying to port Thingy52 firmware project from Keil to SES.
I followed this guide Segger Embedded Studio - A Cross Platform IDE
I manage to build without any errors...
Hi Guys,
I am new to the nrf52 family of chipsets and started my work with a custom board containing the nrf52832 chip and some on board peripherals like GPS and some sensors...
phenomenon:
When master successfully encrypts using previous binding information, pm_evt_handler in main.c receives a PM_EVT_CONN_SEC_SUCCEEDED event and gets a bonded...
I want to read and write certain pages from the NRF52 flash via nrfjprog. The goal is to debug an issue with the peer manager by saving the FDS flash contents to disk. I would...
I have downloaded the Eddystone example to my nRF52832 dev-kit and I am trying to register it with the google beacon platform using their beacons Tools app but it says that...
Hi,
i have the below queries:
In our project we are using multiple masters and multiple slaves, in that each slave is dedicated to a single master.
for ex: we are having...
Hello. I created some HID device based ble_app_hrs_pairing_nfc example on NRF52. And I have a questions:
1.I need to automatically reconnect to bonded device after reboot...
By default, the NRF_DEBUG is disabled. After enabling, and removing this assert check:
devzone.nordicsemi.com/.../
I am now hitting another one here:
#if ( configUSE_TICKLESS_IDLE...
