Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
After sd_ble_gatts_hvx() call, is it possible to change or delete value in softdevice buffer before a connection event ?
Thanks by advance for your help
Best regards...
We have a medical products need to evaluate the maxinum transmission data rate of BLE .i am using is the latest nRF5_SDK_15.0.0_a53641a.
i find to using the ios lightbule...
Dear Developers,
Good Day!!
I want to merge ble_app_att_mtu_throughput & uart example, basically requirement is CLI & other UART communication should work together.
...
See a new landing page on the nordic website for the nRF52840-DK (as opposed to PDK), which states that..
"The nRF52840 replaces the nRF52840 PDK which is not recommended...
We are fine tuning our manufacturing process placing the nRF52840 and would like to know what surface finish is used on the chip. I was not able to find this in the spec.
It seems like a similar IAR debugging problem has been solved but after a day of trying everything...
BLE application with SDK 6.1 and SD 310 1.0 running IAR 8.1 (and identical...
Hi!
Thank you for providing an SDK for BT mesh so early. I'm wondering if you also provide an Android (or perhaps iOS) mobile app that interacts with BT mesh, e.g. by acting...
Hello,
i'm a french student so i'll try to do my best to talk in english with you. I'm trying to use and understand the nRF51822 in order to transmit data to a smartphone...
Hi Expert,
why BLE_APP_UART example can use button 1 to button 4 to wakeup from sleep?
I checked source code I only saw the BTN_ID_WAKEUP is 0.
#define BTN_ID_WAKEUP...
Hi, according to the Bluetooth Mesh Glossary , there are 4 features supported:
1. Relay;
2. Proxy (GATT);
3. Low power;
4. Friend.
Questions:
- Which of these...
We are releasing a firmware update which adds an additional bluetooth profile. Since we do not want or can retest the entire stack, we use a Previously Qualified Design (51744...
I'm using NRF51822 with soft device version 6.0.
I'm trying to create an event which should be triggered every 24 Hours. In the current implementation in our code base...
I saw the demo of nRF52832 connected 20 peripheral devices and control the light in the peripheral.I would like to know the more deatil of the whole operation in chip/SD....
I've searched and the majority of answers seem to be years old.
I have an existing app_timer event handler that works perfectly, blinking LEDs.
I will soon have another...
