Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hi, im using nRF 52 DK. I want to interfac mpu6050 by using the example found on this page https://github.com/Martinsbl/nrf5-mpu-examples . I'm particularly using the example...
hi Support Team,
Mesh 2.0
#if GATT_PROXY if (is_provisioned) { proxy_init(); }
Where is proxy_init() declared and defined..
I am not able to goto definition by RightClick...
We need to measure a pulse width and create an event when it changes. The change will be from 10 to 80 percent, roughly - 1mS to 8mS or more. This is a very loose requirement...
Hi
I have to combine both BLE UART profile and RTC examples of nrf52 of 11.0.0 SDK for my application.When I run them individually, they are working fine.After combining...
Hello,
I am working with nRF52832 and using Keil uVISION 5.
While building the exapmple from nRF SDK v15, I am getting this error :
error: L6236E: No section matches...
Hi, I have nrf52832 and using QDEC driver. In my application I want to use values accumulated in the acc/accread register for a time of the order of seconds. Since max value...
Hi all, I found one issue with my custom nrf51422ble board. When I use my office PC and KEIL IDE, my custom board BLE is working but when I use my home PC KEIL, it's not working...
Hi, I am using https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo with segger embedded studio and nordic thingy52 modules. I have problem with the mesh assert which...
Hi,
I'm new to this product and I'm facing some problems in dowloading the required softwares to program the nRF52 DK, I saw most of the tutorials here and they are old...
I was trying to upload one of the examples which is ble_app_hrs file to test nRF52 DK. However, it gives me a message that i have about 31 errors.
Below are some types...
Hello Everyone,
I am an experienced engineer but actually a beginner with Bluetooth technology. I am working on a project that uses a Fanstel BT832AF Bluetooth module. This...
Hi,
I need to be able to put larger strings in the scheduler. At the moment the maximum accepted values for init are the following:
#define SCHED_MAX_EVENT_DATA_SIZE...
Hi, I am confused by this config.
static void drv_keyboard_gpio_init(void) { // Make sure that columns will drive 0 when they will be configured as outputs. NRF_GPIO->OUTCLR...
I'm using a NRF52840 with S140 softdevice. I advertise some data and I want to be notified when advertising start. I followed this thread and I use the customs ble_radio_notification...
