Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
i've already read a lot about this topic in this forum, but now I'm unable to continue on my own. I wan't to migrate the DFU SDK emaple from Keil to GCC. I already...
Hello,
I am trying to use the nrf24l01+. But I don´t get any signal in the MISO pin. I have the same behavior in all my nrf24l01+ devices.
The MISO pin as always HIGH...
Hi,
I'm despair.
I am trying to receive data from the device with nRF2402G with a nRF24L01 + module.
The old receiver is destroyed.
I believe that I have put all the notes...
A long term problem with the Segger JLink drivers on OS X has been that for composite devices, the Seggers with both a JLink/JTag plus a USB for the UART, like those on the...
I am planning to collect data from multiple ANT sensors with nrf51 dk (like heart rate, cadence...) Collected Data will then be transmitted on a different proprietary link...
Hi!
I'm working with a NRF51822 (not a dev card) and I want to disable and enable BLE by switching a switch.
I've been looking at this thread and the functions bluetooth_sleep...
Hi,
I want to integrate Staticpasskey functionality with bootloader application in our project. as you know that in device_manager_init() function "pstorage_init()" is...
Hi all,
we have an application in which low current consumption is important, therefore we cannot use the GPIOTE IN events due to their ~1mA current consumption ( devzone...
Hello NRF,
Is it possible to have on a custom service multiple characteristics with read and notify options enabled. If yes can you show me a example or give me a hint...
hello , i work on nrf dev kit and i want to make project that the kit communicate to mobile with low current consumption. when i press button it send button press count to...
MCU : NordicSemi nRF51822-QFAC (Using custom board)
SDK Version : 6.1
Softdevice : S110 7.1
Using MDK ARM v4.6
Hi, I want to create a RTC calendar using APP_TIMER...
Hi,
I'm testing new nRF51822 Beacon v1.1.0 dedicated for smart beacon kit (pca20006). I'm using nRF Toolbox app version 1.4 and iphone 4s with ios 8.1.2. I've followed...
Hello， gus
our design will be in mass prodcution stage，I want to find a efficiently way to load our hex file to NRF51822 modules， how to use batch processing to call nRFgo...
