Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi,
I'm trying to implement GATTS Queued Writes: App handled, no attributes require authorization variant #2 VLOC_USER.
According to the documentation values in ATT table...
Was Nordic's MCP named after the MCP (Master Control Program) in the 1982 American science fiction action-adventure film written and directed by Steven Lisberger?
End of...
This is a kind of continuation to: devzone.nordicsemi.com/.../
I'm modifying the bootloader_secure sample to implement encryption.
I'm now at the step where I need to...
Dears,
I am developing my application based on SDKv12.0.0. I would like to use "printf" & "app_uart_get"(interrupt routing) instead of "NRF_LOG". Is possible to switch it...
Hi,
I am asking questions through Google Translator.
The context may not be smooth.
I am planning one project.
Simply put, the usbd_hid_generic example uses bluetooth...
I use nRF51-Dongle as an ANT USB stick, to carry out this test, but the ANTware II can never display the informations of nRF51-Dongle. How can i do it ?
Hello,
there is an equation in the code where I see that variable: deviceid is: 229 and var_temp is also: 229.
But the debugging shows that the Mikrocontroller is going...
I'm seeing the same issue as this question , but I'm on SDK 13.1, which has a different peer_manager.c, so I can't directly use the fix for that question.
Like the other...
Hi,
Scenario:
Two nRF52832DK boards on a table, approx 20 cm from each other, +4dBm output power.
Payload length is ~60bytes.
Running at 1Mbps gives me less than...
Hi,
assuming I have an IMU sensor with 3 different interrupt lines. And I want to start a TWI DMA transfer for each interrupt line in parallel. Is this possible since there...
Hi all,
We are starting new project, the aim of the project is control street lights through web site by using gprs connetion.
The key requirements of the project is...
Hi
I finished preparing the nrf52832 board to use ppk and measured it with ppk.
I am trying to repair the nrf52832 board.
However, I do not understand the contents of...
Hello,
I'm porting the nRF8001 SDK to STM32 using HAL (CubeMX). Communication seems to run fine, however, the setup stops with CRC error. See abridged the logical output...
Hello everyone.
I am developing with nRF 52832.
However, when I call UART_init() function. my source code outputs an error message.
source code is under the line...
