Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi team,
Let me confirm what's C0 in the nRF51 32MHz XO spec. It specifies as following but C0 definition cannot be found in the PS. I assume C0 is the load cap where C1...
Hey,
I’m using Arduino IDE to program my nRF52832. I want to connect two nRF52832’s using BLE for master-slave communication. Eventually I want the master to control multiple...
Hi,
I am using nRF52840 DK, and I am creating my program starting from the basic UART example. I am not using threads, just plain sequential execution. I have a chain...
Hi,
I found out, that in the light switch example (SDK for Mesh v.1.0.1) after adding second element with Simple OnOff model in the light_switch_server, it is not possible...
Hi! Im using a nRF51-dongle and the SDK v12.1. There are no exampels for Segger Embedded Studio but in Segger Embedded Studio im trying to use the "Import IAR EWARM/KEIL MDK...
Hi everyone!
Im using Segger embedded studio and its works well to import the keil project to SES. I dont get any errors when building or debugging but i cant se it in the...
I read that in large networks that configuring the relay nodes helps achieve low-latency communication. With the nRF Mesh, is it possible to automatically switch off the relay...
Hello,
I wanna use FDS module and started with FDS example given in SDK 11.
I have used the exactly same functions for initialization but it seems like FDS module is not...
The S120 Central after scanning, connecting, and issues a sd_ble_gap_encrypt() to secure the link. If the peripheral's bond (LTK) is corrupted or incorrect, the sniffer shows...
This: http://www2.keil.com/mdk5/editions/lite/
I guess the principal limitation is the 32K code size, but the full list is here: http://www.keil.com/demo/limits.asp
...
I have Stlink v2 programmer and I would like to use it to flash hex file into my nrf52832 I read a lot of threads about using tools like openocd but none was helpful, I think...
I'm attempting to build the ble_app_hids_keyboard example from sdk 14 using gcc and the compiler is throwing the error "No such file or directory", but the file is there and...
I have problem on SoftDevice V6.0.0(nrf52832) scan_start/stop. modified ble_app_blinky_c(ble_central) 1. app_timer add (20ms cyclic) 2. app_timer handler, run sd_ble_gap_scan_start...
Hi
The 'ble_app_multiperipheral_pca10056_s140' example for the nRF52840 has an 'LED' characteristic under which there is a "Nordic LED Button Service"
The value...
