Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi All:
i have a trouble, i need Coexistence mesh sdk 2.0.0 provisioner and nrf SDK 15 template. but mesh not work when nrf SDK 15 run advertising_start(erase_bonds);
...
I'm working with nrf24l01 module and use it in BLE beacon mode.
My main question is how can I decrease the visibility range to 10 - 20 santimeters?
(by some schematic...
Hi Support team,
My search for nrf8001 port to Arm-m3 landed me on a thread , where the support personnel has provided a link for a port to lpc1769 in the last comment....
Hi,
I would like to add sensor data in mesh network to be able to send data in certain intervals. How is it possible when I create a sensor model for mesh client and server...
Hello. I have a nRF52832 DK and I'm trying to modify the SPI example code found here:
/nRF5_SDK_15.0.0/nRF5_SDK_15.0.0_a53641a/examples/peripheral/spi
I'm using the nRF52832...
Hello Guys,
I have brought this nrf52840 to try BLE mesh. I tried connecting it to the PC and it was working fine, later I tried dumping the file into the board through...
Hey Nordic and co-nordic developpers,
Just to show some capabilities here at work I want to compile and run the mesh demo on the 10 Thingy52's we have here. I am currently...
Hi Nordic,
Could you please help me ! This is an urgent matter!
Based on this discussion , there is an error rate of actual baudrate comparing with the desired one.
...
Hello everyone,
I'm trying to use the new SDK 15.0.0 and the S140 soft device V6.0.0. I would like to use the LE CODED physical layer and set my TX output power, but when...
Why did the softdevice handler's API change?
sorry for a general question. I used SDK 13. and Now, I am porting my software to SDK 15. So, I have simple question. Why did...
My application is based of the UART example, I have a repeating app timer that fires every 5 min's to do some tasks, I also utilise single fire timers (initiated for events...
Ok, so I am using nRF52DK and trying to figure out to how to send up to 6 packets of data from custom service that sends 6 16bit values per packet. When I send one packet...
Hello,
We have a custom boards that powers a NRF52840 module from a 1.8v voltage regulator coming from a 3.6v battery. We also connected the positive pole of the battery...
I am new to embedded development. How do i physically connect the sensor to the board?
Is it possible without any additional equipment? What is important regarding pins...
Hi,
We want to certify a product embedded nRF51822 chip, with BAS and IAS defined by Bluetooth SIG.
Requesting SIG certification for it of a certification body, we were...
