Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
hello:
I'm looking for a bluetooth solution for our equipment. We need a chip that simulates a serial port, what we send by SPI port, it is received in the mobile and the...
Hello,
I would like to understand how can I make use of the macro ERR_TO_STR_TWI in order to know what error is being given by my TWI module function.
I have tried something...
I am attempting to run the SoftwareSerial example on the Arduino Primo.
The example code does not work and I am wondering whether the pin assignments are correct.
Example...
If I use PWM "nrf_drv_pwm_simple_playback"
and that will go to "start_playback"
How can I catch end point after it finish entire function?
BTW, the process will keep...
Hello All,
I am working on nRF52-DK, nRF52832 PCA10040, and i want to know on how i can wake up my device from sleep mode using hardware interrupt. I am using interrupt...
Hello,
i want to power off and on the board using the Long Press Button Event.
Is this possible? Please help me out to resolve this issues...
Thank You
I used to get all my output by running cat on /dev/ttyACM0. Now I only see the first few lines, until the filesystem gets mounted.
How do I prevent Linux mounting the filesystem...
The Bluetooth Mesh Light Switch example provides an example of how to program a Bluetooth Mesh application where the client model is on the provisioner device and the server...
Hello
what we want :
One central and several periphals.
The periphals will have different DEVICENAME.
Is this possible with the NUS Service?
The doku says ;
Note
...
Hi all,
Anyone has tried if the Tx power of nrf 51822 is changed from +4dBm to -20dBm, how much power (%) can it save, in a ballpark figure?
Thank,
Carl
hi
i am using the sdk 12.3.0 when i'm trying to compile the file under blinky/pca1028/s130 i'm getting this error anyone can help me please
............\components\softdevice...
I am using S132 V5.1 in combination with nRF5 14.2, and I cannot find where I can set hvn_tx_queue_size.
We are using the new option to configure the softdevice using the...
any one can help me to fix this erreor please
............\components\ble\ble_services\ble_nus\ble_nus.c(41): error: #59: function call is not allowed in a constant ...
Hi,
I am trying to send an command line through UART to the UART device such as MP3 audio module.
MP3 module is taking only hex values. How to send it to the UART device...
Hello,
I have connected my PCA10040 to a SIMCOM SIM5320 WCDMA modem and I am trying to make my PCA10040 a gateway for other BLE devices to send data over a cellular network...
