Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi!
I've found mismatch between schematic reference from Product spec ( here , page 692) and PCA10056 PCB (Preview Development Kit) for same operational mode.
In specification...
Hello,
i am using the Nrf52,
i am facing problem on the following line
#define MESH_SERVICE_BASE_UUID128 0x23, 0xD1, 0xBC, 0xEA, 0x5F, 0x78, 0x23, 0x15, 0xDE,
0xEF...
Hello DevZone community,
Currently I am using nrf51822.
Could you guys please tell me how to enable code protection besides check the "Lock entire chip from readback" in...
Dear All, Please update me if is it possible nRF52810 is having capability for SIG Mesh or Mesh Network? Also is to possible to establish Mesh network beetween nRF52810 as...
Hi All,
We received a new design with a nRF52 powered at 1.8V. We are using a JLINK probe with the SW protocol for the burnin code.
When we apply 1.8V we can’t program...
The function find_adv_name() found multiple time in BLE central examples is using the global variable m_target_periph_name instead of the parameter name_to_find . There is...
heelo every one ,
i want to use bluetooth to connect my nrf51822 to my smartphone can anyone help me because i don't have any idea there is any example ready to use pl...
nrf52832dk pca 10040 board
besides ports bits and dir setup and baudrate, etc ...
this is part of my uarte init funct (pDev = 0x40002000)
pDev->TXD.PTR = (uint) TxBuf...
nrf52832dk pca 10040 board
besides ports bits and dir setup and baudrate, etc ...
this is part of my uarte init funct (pDev = 0x40002000)
pDev->TXD.PTR = (uint) TxBuf...
I just bought a nrf51 dk to master this wonderful SoC series.
For now I intend to keep my research and studies with Bluetooth 4.1, but would like to prepare for a jump...
Will uarte interrupt call NRF_LOG_INFO, will run away the possibility of the processor? backend uses RTT
I set uarte receive dma buffer to 10, then the sender to use the...
Hi all, we have a problem with a project based in nrf52832 and a custom board. The project is based in "ble_app_uart" example, and also we have the following sensors:
Accelerometer...
hiii friends,
i have developed new board using nRF52832 xxAA. i am dumping code in this using nrf52 DK and it is working fine but when i am removing power from this and...
