I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,
I use the pca10040 and the problem is in 14.0 eaxmple ,when I push the button switch the protocol mode like : ble->gzll->ble and then I find the example loop into...
Hello,
based on the saadc example of SDK 11 I am trying to change the code to use the SAADC's local timer to sample the input given number of times (10 times for the below...
Hi,
well I struggle with another problem right now.
In case of some errors, I use 'sd_nvic_SystemReset' to reset the system.
But the WDT is used in the application. Thus...
Hey guys,
how can we use DSP math functions on the nRF52832 little monster?
Is there somewhere some documentation?
What about power consumption and performance?
...
Hi, I'm using blinky from the SDK12 as an example here with a nordic nrf51 DK (pca10028, onboard nrf51422) which I am using as a programmer with a custom board (with a nrf51822_XXAA...
Hi guys, just signed up here for some help.
I was learning how to develop a project with nrf51822 core chip. The one I'm using is this one . I also have a DK for the nrf51...
I'm attempting to change phy in a program based on the UART example and am following the same process used in the att_mtu_throughput for changing PHY.
Calling sd_ble_gap_phy_request...
Hi,
I'm using nrf52 + SDK11 + softdevice 132 2.0 and trying to integrate
the OTA dual bank bootloader. Using the nrfjprog tool I program the
softdevice + bootloader....
I am using the nrf52832 soc, and have a requirement to run the device in low power mode and using the timer with a timeout value in days? how can I do so?
Sample code would...
I want to read data, advertised by a bluetooth beacon.
I have made this work before with SDK v14 using NRF_SDH_BLE_OBSERVER() to register a handler function to handle BLE_GAP_EVT_ADV_REPORT...
As a complete newbie to this a bit of guidance would be really helpful to point me in the right direction.
I want to create a simple device with a couple of switches (physical...
Hi Nordic community,
I'm sending several packets from nrf51822 (custom board) to Android application. At the moment I want to configure the sensor by sending commands from...
hi,
I tried to recover custom nrf52 board by nrfGo stuidio,and it failed,the logs as below:
------------------------------------------------------------------------...
Hi All,
I'm using a sdk11 and i have started using the glucose profile example to use a peer_Manager.
I have modified it to have a just work behavior. It works correctly...
We have a potential application where we have to send data over BLE at 3kbps and store in external flash memory at 8kbps. The last memory accessed in external flash memory...
