I'm trying to flash the hardware even with Programmer v4.6.0 but i get the following issue
18:59:55.179 Initialising the bundled nrfutil device 18:59:55.561 Using the...
Happens consistently and in production.
The stream advertisement is still there but cannot be connected to by any receiver (both 3rd party and our own). 3rd party says connected...
Dir Sir
I have bought thingy 91 X for evaluation purposes
After activation of the Sim and, I have a constant green Led on
The device does not connect to the web application...
I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
Hi there,
In our device we are using nRF52832 with SoftDevice S112, SDK 17.0.1 and embOS Safe. Up until now we were working with the “Just Works” setting of BLE connection...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Hi there
I have encountered another issue with a repeater that I am working on.
The program follows this basic sequence:
Setup as NRF_GZLL_MODE_HOST
Wait for...
Hi, I am trying to use NRF_CLOCK_LF_SRC_RC as clock source with the following settings:
pca10040.h
#define NRF_CLOCK_LFCLKSRC {.source = NRF_CLOCK_LF_SRC_RC,
.rc_ctiv...
Hi,
Am having application with Freertos in which am creating 4 tasks + ble task using Freertos API's. Application is running as expected without any issues.
But in 4...
Am flashing SD 3.0.0 and secure Boot loader and then updating application (with Freertos) via bootloader .Application boots up no issues.
am facing below issues.
1.Am...
Hello,
I've checked the timing diagrams for the CE and IRQ on the datasheet but I would like to know if anyone has actually tested them with an oscilloscope? If yes could...
I am using SDK 11.0.0 on a nrf52832, with FreeRTOS and SD132 2.0.0. I configure the FreeRTOS port so that it uses RTC1 as SysTick. Depending on some compilation macros, my...
Assuming that all peripherals that require the high frequency clock are disabled / turned off / stopped, how long does the HFINT oscillator run after calling __WFI()?
And...
What's the delay from setting the Start / Stop task in an RTC module to when the RTC actually starts or stops? Is it less than 1 clock cycle on the CPU (15ns)? More than one...
Hi, I am using the nrf52 dk to sample two analog inputs through PPI.
My question is if I can use different bit resolutions for each analog input?
-Erblin
Hello !
I have a problem with my program (on a nRF52 board) : when I send a value to the board via BLE, it seems that my static variables are reset.
I noticed that, because...
I need to store data in some moments and if something happen i have to read those data, i have to do a log events.
I use nrf51-dk and soft device s130. This data is taken...
"....\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production. Please see github.com/NordicSemiconducto.. . to generate it.
i found...
nrf51 dk with 51422 device (10028) was running in Segger Embedded Studio example imported from IAR / Keil ble_app_cscs_pca10028_s130 SDK12.1.0 was just fine. I loaded couple...
