Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
In the nRF8001 Product Specification, section 7.1.5 it states:
"The maximum length of an event packet
is 31 bytes, including the length
byte."
In the headers...
Has anyone seen more than 3 notify packets per 7.5ms connection interval?
I am seeing 3 and am wondering if this is a fault of the way my app is working.
My Setup:
Nordic is the Server, Android is the client.
I have read many, many forum posts about doing long reads/writes. Virtually everyone says you cannot do long writes...
I am trying to connect more then one device to nrf51822 HID.
How can i pair more then one device ?
How can i delete paired device from nrf51822?
Thanks
Recently ran nRF Master Control panel on android and found "Read remote RSSI" button. Is data got from device in some way or simply measured by androd phone ble radio module...
I would like to write to multiple characteristics in a loop but the second call to sd_ble_gattc_write() causes a NRF_ERROR_BUSY error. From reading the documentation, I should...
Hi all,
I am working with PCA10028. I have a peripheral and central both are devices with no display and no keyboard. both peripheral and central device are under our control...
Hi,
I am using nrf51822 with s110 softdevice version 8.0.
Is there any way i can know the state of my radio at some point in the code execution?
In short I want to access...
As explained by electronut in his Blog and Lijun here , it is possible to program an External nRF51822 board using the SWD interface of the nRF51-DK.
But what about a custom...
I have a project, and nRF52832 it 's good chip for me, because it has NFC/ bluetooth communication.
I would like to know if nRF52832 can pilot epaper display. nRF52832 does...
Hi,all. i face a problem. the office DFU flowchart is device reset--->bootloader --->upload firmware to device ---->device reset.i want to implement as follow: upload firmware...
Dear all
We did nordic beacon board in that we not able to flash the device
We are checked core voltage 1.2V and 1.7V are coming .But i want to confirm external CLOCK will...
Hi,
I want to change the interval time of 51822 dongle with the instruction here devzone.nordicsemi.com/.../
The default value is 100ms as following
#define NON_CONNECTABLE_ADV_INTERVAL...
Hey guys,
I’m working on an nRF51822 design where I’d like to check the value of a GPIO at Power-ON, then either shutdown, OR start the BLE stack and do BLE stuff. I really...
when compiling " ble_app_proximity " exampled by Nordic, it indicates errors:
" D:\Program Files\MDK5\ARM\PACK\NordicSemiconductor\nRF_Drivers\3.0.0\gpiote\nrf_drv_gpiote...
