Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I am using the 8.1.1 version of the SDK on a Rigado BMD-200 device, s110 version of SoftDevice.
The code has set APP_ADV_TIMEOUT_IN_SECONDS to the maximum (all bits set...
My main App must be able to use the soft device directly or serialisation when a external Connectivity chip is used. How can this be done? In the examples it's done at compilation...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards.
I want to check my runtime.
So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Looking at the nRF51 UART Example, i know that all packets transmitted over a BLE link will be protected by CRC on the link layer.
But how about when nRF51 scan the ibeacon...
Hi, I would like to use RTC1-> cc[1] using app_timer drivers. How to do this? Examples show only the usage of RTC1->cc[0]. RTC1->cc[0] has been used by ble_conn_params.c and...
Hi,
After few hours my program is crashing and I'm landing on address 0x1AFF4 which belongs to softdevice. For what is responsible this code and what could be a reason...
Hi
I am using Nrf51 and Softdevice S130.I know that softdevice S130 supporting Ble 4.2.This will act as a peripheral.My mobile phone supporting only Bluetooth version 4.0...
At s120,i used the following code to send data (to s110)
if( ( wIndicationFlag_Get() == true ) && ( wConfirmFlag_Get() == true ) )
{
//APPL_LOG("Write Data\r\n");
...
Hi Nordic,
From the topic: APP_TIMER_TICKS value , I've know how to use it, but is it possible to use different prescaler value in the same code?
For example the nRF5_SDK_12...
Hi, I need help for generating the init packet. I'm using SDK 11.0.0 , s130 on nrf51822. To build bootloader, I've used the sample bootloader with some include path changes...
I try to print the RSSI level but i couldn't do.
I use nRF51 DK and soft device S130.
This is the line that i just write:
SEGGER_RTT_printf("RSSI: %d\n",p_gap_evt-...
I'm trying to create a project from scratch that can use the S132 Softdevice, but I am constantly running into problems trying to get the correct headers, preprocessor macros...
Hello Nordic,
I am using the BL600 third-party module and SDK 10.
I was able to modify and compile project with GCC at
examples\ble_peripheral\ble_app_uart\ for s110...
