I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I'm trying to apply a firmware update using a zip file that has worked with older version of nRF Toolbox. Using the current version, (4.1.1) on iOS, I select DFU, then select...
Hi everybody.
I am opening a dedicate question after a recent topic that already helped me a lot, with another discussion pretty similar to my problem. Resuming briefly...
On the nrf52dk development kit, I want to power the target nrf52 from an external supply without powering the interface mcu (the debugging probe). How do I wire that? I don...
I'm trying to add nRF_Drivers files to Segger studio project, based on nrf51,51422(10028) examples. I added path in preprocessor user definitions and I added file like nrf_drv_lpcomp...
I set up my PWM Driver like this:
nrf_drv_pwm_config_t const nrf_drv_pwm_config =
{
.output_pins =
{
BSP_LED_2 | NRF_DRV_PWM_PIN_INVERTED, // channel 0
NRF_DRV_PWM_PIN_NOT_USED...
Hi,
I would like to test my C code with bootloader over air by BLE. I am using nrf51822 with soft device 110. Does Nordic Company is sharing any application which can bootload...
So this might be one of the most confusing issues i've come across sofar. We're currently developing a product based on NRF52 (more specifically NRF5283 QFAAB0) with a custom...
Is there firmware available as binary file that can be loaded to the nrf52832 that allows connectivity to is as a UART HCI compatible device?
Would the same firmware be...
Hi,
I am using "nRF Toolbox -> DFU" to change an application on my BLE module which contains; nRF52 device, SDK->v11.0.
I am using ".hex" file to load the application...
iphone5_b.psd m370_android6_b.psd long_write_error.png I using SDK11. I porting nus profile to my system and make a customer's UUID. I use Lightblue on iPhone 5 to connect...
Hi,
I would like to know, by using nRF528322 Development Board can we dump the code into another hardware like custom nRF51822 microcontroller..??
If Yes, What are the...
hi , need a urgent help on small problem but really not getting ahead bcos of it.
I'm using NRF52, SDK v11 , Software Device s132.
I'm calling sd_ble_gatts_value_set() like...
The struct type nrf_saadc_config_t is defined in ../hal/nrf_saadc.h but is not referenced anywhere else in SDK v12. Thus it is either cruft, or more likely, the function nrf_saadc_init...
Hi.
Is it possible to use SPI slave and SofDevice at the same time? I try to do device which status will be read by master uc by SPI. I'm using nRF51422(rev.3), SDK10.0...
