Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi all!
My project is depend on the "ble_app_template",which uses the "scheld structure", I am able to read the data from app but not able to send my data with notification...
I have a question about that code, when I test my code with lightblue, it showed me that there is an service called application notification client service, but it didn't...
I'm using GPIOTE library to check the change of two switch inputs.
Normally it works well, but rarely GPIOTE_IRQHandler become never happen even if the pin level changes...
Hi Nordics!
I am using app_pwm.c file in SDK 8.1, and when I use it with softdevice(advertising or data transfer event), sometimes pwm signal is reversed.
I guess, reversed...
Hi Guys,
I am using a the 350Mhz Analog Oscilloscope HM303-6 www.hameg.com/hm303-6.0.html to measure the voltage utilised by the board when it is transmitting data.
...
Hi,
Once I enter into BLE mode I am not able to read any gpios(nrf_gpio_pin_read) also I am not able to set any gpios (nrf_gpio_pin_set).
Below is my example
uint8_t...
I'm trying to establish a bond in my project and then perform service discovery, however the discovery is returning the BUSY error.
I tried to wait for the events according...
In SDK 8.0 the bare word asm was re-introduced in nrf_delay.h , causing failures in compilations that use strict C/C++ standard conformance flags. This was noted in earlier...
Hello Developers
I have to solve a problem for which I could not find much information about online, so I am hoping you guys can help me.
I am developing a WIN32 application...
Hello, For some reason the Ble App Uart is not working on my PC anymore. I have gone over Nordic tutorial again however, the LED doesnt blink and I cant detec the device on...
Hi,
What are the general causes of SDS assert in nrf51/52 ? Assuming that SW has been tested, is there something that could happen in the code that would cause the assertion...
Hi All,
I'm using "scanForPeripheralsWithServices" of iOS to the BLE devices.
"scanForPeripheralsWithServices" sometimes never return anything.
I have to stop scan or...
Hello! I'm trying to build a program for nrf51822 via QT Creator.
I'm using QBS for build. I have a makefile from SDK examples for nrf51822. Someone can help me, how to setup...
Hi all,
I have the exact issue mentioned here - github.com/.../9
I have updated my makefile to generate only one bin file from the Softdevice Hex file, but still I'm getting...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
