We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Is there any way i can get UTC time?
Is there any real time clock which keeps track of the time even if the chip is off?
I am using nrf51822 and require the UTC time...
Hey everyone,
I'm having problems with my app's ram usage as you can see from my previous questions.
I've tried this little piece of code:
void memcheck(void){
...
hello friends,
Im developing an application where im trying to connect a central and a peripheral but since the signal strength depends upon run time environment i am getting...
The App ~ BLE Stack is the device, Central is smartphone.
is correct?
I don't understand this sequence.
Do not adv_data_set and the adv_start before the scan?...
I'm attaching a function where I use the sd function :
void edit_speed_ID(uint8_t speed)
{
uint32_t value;//, err_code;
value=5 * speed;
while(sd_flash_write(address...
Unfortunately it seems my post devzone.nordicsemi.com/.../ has been lost.
This is a re-post.
I am trying to manipulate Flash data in CODE_SPACE one page at a time. Currently...
I'm using nRF51822 for ble.
For my application, I need to increase rf power.
( My application needs +10dBm)
In case of CC2540(TI ble chip), there is application note...
Hello,
I have 2 nRF51822 with S130. One is central, the other is device.
I want to exchange custom data between these 2 devices after connection. What is service best...
Hello,
I do communications between 2 nRF51822 (one central and one device). Once they are connected, cant i do a kind of deep sleep and freeze stack state for 1 minute...
I'm getting a hardfault on some float operations that I wasn't getting before I upgraded to SDK 6.0.0 and SD 7.0.0. At least, I wasn't getting them at all before that and...
Hi:
I use spi0(0x40003000) to wirte data to external flash(W25Q64) with SD8.0(sdk8.0.if I write data without sd, it is OK), and when program run to rx_data[number_of_txd_bytes...
A friend of mine asked me to help with thinking about a solution to create a RF communication between 8 robots and 1 access point. Not a lot of traffic, just to signal that...
Hi everyone,
We are making a BLE peripheral that measures some data and keeps it ready for the mobile phone to connect & poll the data.
The data should be private and...
I am trying to use the template to create my own application. In two places I have read, that to add my own services, I just "Double-click the Serives folder in the Project...
Hello everyone,
I had some troubles some time ago with Softdevice s120, and finally solved it to work with nRF51822 thanks to Aryan .
The problem is that, when I upload...
