Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi.
To avoid via in PAD I like to route a signal/pin from the inner row (closest to center) through a pin in the outer row.
However, to be able to do that I must be sure...
We are using SDK_13.0.0_04a0bfd and want to change the location and size of the bootloader in flash. But when we do this, the bonding process in the main application doesn...
I'm a newbie to nRF5... I just installed latest IAR, nRFgo, Segger J-link & nRF Connect on Windows-10. Segger J-link appears to have updated nRF51 Dongle to 6.3. I get the...
I'm developing firmware for a client that includes a connectable beacon. I'm using code based on a Nordic example, though I can no longer find the original. I'm trying to...
In our project nrf52 device scans for nrf52 beacon device throughout the day. It scans number of beacons available and send it to esp32 device on serial. that is how its working...
Hi, Everyone
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
The size of the file has increased dramatically when I run mergehex.
1. nrfutil settings...
Hello i'm currently working on the central part of the DFU i succeded to make it work and now i'm working on the link loss part.
I used This to make the DFU work but it...
Hi,
I am facing the same problem as in question ' USBD don't work with debugger ' from @ Dusautois Jérôme
I am trying the same code both on PCA10056 and my board. In PCA10056...
Hello! I am useing nRF52832 with custom-made board.
SD 5.0.0 and 14.0 SDK
I am using modificated example of "ble_app_template", i added simple custom service from example...
I'm using USB based DFU on Windows and on Linux 18.04 LTS VM on Windows.
Platform: nRF52840-Preview-DK
SDK version: 15.0.0 (nRF5_SDK_15.0.0_a53641a)
example USB Secure...
Hi everyone,
I was just going through the library functions provided here in this link : nordic functions twi
But inside all these functions ,there is this parameter...
platform : nrf 52832 SDK : 14.0.0
I used gpiote to detect sensor's interruption . there are two sensors ,so I configure the gpiote like this :
neither of the two sensors...
Hello, I want to ask if is possible connect nRF51 Dongle in Shield Host USB ( https://www.electrofun.pt/usb-host-shield-android-arduino ) with arduino .
Thanks very much...
Hi!
My design has to be tested at 50V/m according to MIL-461F. Are there any experience with this high field strength or the MIL-standard? I want to avoid the cost of shield...
We are currently going through certification and have had an interesting failure during radiated emissions. When in normal transceiver mode, all is well, but when we put the...
