Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello! I am new to the Nordic and Bluefruit enviroments.
I am currently working on getting a scan response request from the scanner to the advertiser and have the advertiser...
Hello devzone,
There are 3 {37,28,29} channels for advertisement & i want to advertise only on 37.
Soft: Nordic mesh v1.0.0 stack & pca10040 nrf board, light switch example...
Hi, I'm trying to controll the port of my nRF52832 by writing to a characteristic value. So far everything works fine but I'm unable to get the value of my characteristic...
Hi all,
i development a FW with a low power and when i measure the power consumption using a nrf connector on evaluation board i have 2 ua, and it's ok. Now i have the some...
So I can see the "API Reference" documentation on the UART driver in the info centre, however this is all very low level and I am going to waste hours going through all this...
Are there any changes required to run the Sample Bluetooth Low Energy (BLE) applications from nRF5 SDK v14.2 when migrating from nRF52840 IC Rev A to Rev B? I have followed...
Hi,
I am using the nRF52832 on a custom PCB and I am interfacing it with a flash memory chip through SPI.
I am testing the SPI communication using the spi example (nRF52...
Dear Sir,
1. The HFXO crystal can be with load capacitance 12pF? or 8pF is better?
2. According to the datasheet, "17.1.1 64 MHz crystal oscillator (HFXO)"
there is...
Hello,
we have two custom boards with nRF51822.
We use NUS.
If our pakets under 23 Bytes everthing is fine ....
If we want to sent paket with 140bytes, the central...
Hi!,
I've made a custom board using Taiyo EYSGCNZWY bluetooth module, to be used as central in a project. To use this module, several changes have to be made in the clock...
Hi,
I am using nrf52840 to verify a signature using RSA and cryptocell c310.
I get error 0x07 when I try SaSi_LibInit();
My rndContext and the buffer are both declared...
Good afternoon.
I have bought a "nRF51822 Bluetooth Smart Beacon Kit (nRF6930, Rev 1.3.0)" this is the first time I work with this, docs say that it has installed softdevice...
On the current version of the nRF5 SDK we could only use up to 3 instances due to the hardware limitation on the Engineering A of the silicon,
nRF52840 Engineering A
...
.
Included an example picture, not at all the only issue. Using the new DevZone on iOS isn't a great experience. New devZone I think will be a lot better for everyone...
