Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hello All,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART i changed the uart pin configuration as...
dear nordic employee:
I want to use the PPK measure my hardware
I set as the 《PPK_User_Guide_v1.1》 says,and the led1 is ok
but the ppk cannot work well
the details like...
Hello! Is it possible to subcribe on more then one characteristic (which support NOTIFY) on nRF52832 (in Central role)?
I check it in nRF Connect app, it's working, so probably...
Hi，i use SDK13.1 and nRF52840.I keep the DFU_APP_DATA_RESERVED equal to the FDS_VIRTUAL_PAGES.When i change the pages of them to 200,OTA was broken off when starting DFU.When...
SDK13, S132, nRF52832.
I use whitelist and bond peripherails. But after bonded 20 pcs of peripherials, I can work with only first 8 bonded.
Which parameters should change...
I’m trying to create a nRF8001 device without the need for any keys, because the device will be inaccessible in mounted condition. Additionally the connection must be secured...
I am utilizing the nRF52832 with softdevice S332 with both ANT and BLE enabled (no peer manager). When I set the ANT search for a channel to use ANT_WAVEFORM_FAST it causes...
Hi,
I am trying to use fds file system to save some data in flash,
when using the example code of sdk 14.0.1, it is not normally operated,
NRF_ERROR_INVALID_PARAM error...
Hello
I am using nRF51822 Nordic controller, SDK 9 and S130 Soft-Device.
I have used to generate a 1 KHz PWM signal successfully using timer 1.
And generating a 4 MHz...
Hi,
I have designed one custom board using nrf52810 and GPS module. where i can get the gps data via UART to my nrf52810 chip and then from nrf52810 sending same data to...
Hello Sir,
we have designed custom PCB using nRF52832, I am little confused for is it OK. I have attached top and bottom layer layout of my PCB please sir review it and...
Hi guys,
I'm struggling over some basic concepts related to the Mesh SDK, specifically with the Bearer layer and why the Mesh SDK uses the Timeslot API. I'll try to explain...
Hi all,
I'm trying to writing a device information service client on top of ble_app_multilink_central example on nRF52830 using SDK14.1.0 and softdevice 5.0 and have a...
Hello World,
I checked the Developers Zone, but I have not found the direct example of my problem.
I use the RuuviTag board with NRF52832_XXAA.
I use it as a development...
Hello,
I have question about signal names in datasheet nRF52840.
On the pins B19 and T2 on page 14 both pins have the same initial signal names (P0.11).
Please send me...
