Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
I can run the SAADC example and read the analog inputs fine, now I've modified the code to simply read the adc with the blocking nrf_drv_saadc_sample_convert call
All I...
Dear All,
while testing an own nRF52832-based PCB and an nRF5840 PDK for current consumption, I compiled and flashed the code below to both devices. Since then I am not...
Hello All,
I don't find any example of Dynamic Multiprotocol of ESB and BLE.
The current multiprotocol example in Nordic’s nRF5 SDK is a switching solution for multiprotocol...
Hello,
Here is a summary of my main transmission protocol:
The (unique) client contact one of the many servers to get the value of a particular server's state.
In the...
hellow nordic.
i use sdk14.2 ,but pstorage_update return NRF_ERROR_NO_MEM.
i use NRF_SDH_SOC_OBSERVER(m_soc_evt_observer, 0, sys_evt_dispatch, NULL) to creat sys_evt_dispatch...
I have a couple of "cannot-be-resolved" issue with Eclipse.
Issue 1:
Sometime when I set up a project in Eclipse, it runs into an issue where types like uint32_t or...
Hi,
I'm trying to send sensor data via BLE to Processing. If someone has already done it, could you post your code or help me explaining how to approach the problem?
I...
Our Nrf51822 will disconnect the connection with timeout reason when it is sending a large amount of data (about 20-70 KB) to our central device which is TI cc2540 . This...
Hi Nordic.
I have questions about preserving device unique information such as device id and so on. (The information will be written in factory)
I know the best way is...
I am trying to add I2C/TWI bus to nrf51822 device. I have used the SDK example code (12.3.0) and keep getting the following errors:
sdk/drivers/nrf_twim.h:69:38: error:...
Hi, Is it possible to make the same nRF52832 device to function as a master for some interval and then switch it to slave?? i.e, Does Nordic have a single SoftDevice capable...
Hello, the current QIAA package is rather demanding on the manufacutring and significantly increases our cost, are there any alternatives? I failed to find any in the datasheet...
Hi !
My goal is to create a large mesh network (over 100 nodes).
I plan to have 3 kind of nodes : a client (connected to a PC), several server relay nodes (not on battery...
Hello,
I have got a question about gpio current protection in nRF52 - I have checked forum but I haven't found answer on this specific question. In nRF52 specification I...
